Temperature Limitation; Maintenance - HANSGROHE 10700 Serie Montageanleitung

Attention! The fitting must be installed, flushed and tested
after the valid norms!
Adjustment
Correction is necessary if the temperature measured at the
take off point differs from the temperature set on the scale.
To adjust temperature proceed as follows:
Turn the setting knob until water at a temperature of 38°
C comes out of the outlet. Loosen screw of setting knob.
Remove setting knob and turn to the 38° C position.
Attach setting knob again and tighten the screw (please
see page 69).

Temperature limitation

The temperature is limited by the safety check to
38° C (100° F). If a higher temperature is required, it
is possible to override the safety stop by depressing the
safety button.
Safety Function
The desired maximum temperature for example max. 42°
C can be pre-set thanks to the safety function (please see
page 68).
Technical Data
Operating pressure:
Recommended operating pressure:
Test pressure:
(1 MPa = 10 bars = 147 PSI)
Hot water temperature:
Recommended hot water temp.:
Rate of flow by 0,3 MPa:

Maintenance

There is no special maintenance for thermostats. The non
return valves () must be checked regularly according
to DIN EN 1717 in accordance with national or regional
regulations (at least once a year). At this time, please
also check the filter (0.1) situated on the MTC-thermo-
element (0). After assembling the MTC-thermo-element,
it is necessary to check the water temperature at the take
off point as described under the headline „adjustment".
Before the adjustment, please check, if the warm water
supply is activated and the maximum temperature of the
warm water is available at the take off point.
To guarantee the smooth running of the thermostat, it is
necessary from time to time to turn the thermostat from
total hot to total cold.
14
English
Spare parts (see page 4)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
max. 1 MPa
19
0,1 - 0,5 MPa
20
1,6 MPa
21
22
max. 80° C
23
65° C
24
approx. 26 l/min
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
handle for thermostat Starck /
Starck X
handle for thermostat
Carlton "lever"
handle for thermostat
Carlton "cross"
handle for thermostat Steel
handle for thermostat Montreux
handle for thermostat
Terrano "lever"
handle for thermostat
Terrano "cross"
handle for thermostat
Uno / Citterio M
handle for thermostat
Citterio "lever"
handle for thermostat
Citterio "cross"
handle for thermostat Massaud
face plate
face plate Starck X
face plate Massaud
face plate Montreux
face plate Citterio
face plate Citterio M
sleeve
sleeve Massaud
thermostat cartridge
noise reduction
non return valve
shut off unit
sub plate
fixing screw
sleeve
handle Starck / Citterio /
Massaud Citterio M
handle Uno / Terrano / Steel
handle Carlton
handle Montreux
extension set 25 mm
extension set 22 mm
extension set 22 mm
Citterio / Starck X
extension set 22 mm Citterio M
adapter for handle
adapter for handle
adapter for handle Massaud
screw
hollow set screw
10391XXX
17391XXX
17994XXX
35391800
16594XXX
37391XXX
37994XXX
38391XXX
39994XXX
39391XXX
18097000
96551XXX
97925000
98686000
98668XXX
96751XXX
98919000
96439XXX
98734000
94282000
94073000
94074000
94009000
96447000
96454000
96446XXX
96520XXX
96421XXX
96449XXX
98637XXX
13595000
13596XXX
97407XXX
98860000
96435000
96451000
98701000
96525000
97669000