Electrical Safety - ATIKA ASP 5,5 Bedienungsanleitung

Carelessness, failure to comply with the safety
regulations and incorrect use can result in injuries to your
hands and fingers when the splitting blade is moving.
Risk from electricity, by using non-standard electrical
connections.
Touching live parts of opened electrical components.
In addition, in spite of all the precautionary measures taken,
non-obvious residual risks can still exist.
S a f e
S a f e
Before commissioning this product, read and keep
to the following advice. Also observe the preventive
regulations of your professional association and the
safety provisions applicable in the respective country, in
order to protect yourself and others from possible injury.
Pass the safety instructions on to all persons who
work with the machine.
Keep these safety instructions in a safe place.
Make yourself familiar with the equipment before using it,
by reading and understanding the operating instructions.
Do not use the machine for unsuitable purposes (see
"Normal intended use" and "Working with the log splitter").
Ensure that you have stand in a secure standing
position and maintain your balance at all times.
Take up a working position which is close to the
controls. Fig. 9
Never stand on top of the machine.
Pay attention at all times. Take care with what you are
doing, and approach the work sensibly. Do not use the
machine:
− when you are tired.
− under the influence of drugs, alcohol or medications
that may impair your powers of judgement.
When working with the machine, always wear
− protective goggles or face mask
− safety gloves
− hearing protection
− safety shoes with steel toe-caps
Wear suitable work clothing:
− do not wear any loose-fitting clothing or jewellery,
since these may be caught or trapped by moving parts
Within his area of work the operator is responsible for
third parties.
The machine may not be operated by children or young
people under the age of 18.
Keep children away form machine.
Never operate the machine if other persons are in the
immediate vicinity.
Never leave the saw unattended.
Keep your workplace in an orderly condition!
Untidiness can result in accidents.
Do not overload the machine! You work better and safer
in the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on
the machine that could impair the safety.
w o r k i n g
w o r k i n g
Faulty or damaged parts in the device must be replaced
immediately.
Do not spray machine with water
(this is hazardous due to live components).
Do not leave the machine standing in the rain or use
when raining.
Store the unused machine in a dry locked place away
from the reach of children.
Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− carrying out servicing and repair
works, removal of faults
− Transporting
− leaving unattended (even during short interruptions)
Check the machine for possible damage
Before continuing to use the machine, the protective
−
devices must be inspected to ensure that they work
perfectly and with their intended function
Check whether the movable parts function perfectly
−
and do not stick or whether the parts are damaged, All
parts must be correctly installed and fulfil all
conditions to ensure perfect operation of the machine.
Damaged guards and parts must be properly
−
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
Damaged or illegible safety warning labels should
−
be replaced immediately.

Electrical safety

Electrical connections must conform to IEC 60245 (H
07 RN-F) with a cable cross-section of at least
⇒ 230 V ~
3 x 1.5 mm² for a maximum cable length of up to 10 m
⇒ 400 V 3~
5 x 1.5 mm² for a maximum cable length of up to 10 m
Never use the machine with a power supply cable of over
10 m in length. Longer power supply cables will cause a
drop in voltage. The motor will not be able to provide its
maximum performance and the operation of the machine
will be impaired.
When laying the connecting attachments, be sure that
they do get crushed or bent, and that the plug-and-socket
connection does not get wet.
Do not use the cable for purposes for which it is not
meant. Protect the cable against heat, oil and sharp
edges. Do not use the cable to pull the plug from the
socket.
Regularly check the extension cables and replace them
if they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for
outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
16