Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Electrical safety
Electrical connections must conform to IEC 60245 (H 07
RN-F) with a cable cross-section of at least
⇒ 400 V 3~
5 x 1.5 mm² for a maximum cable length of up to 10 m
Never use the machine with a power supply cable of over 10
m in length. Longer power supply cables will cause a drop in
voltage. The motor will not be able to provide its maximum
performance and the operation of the machine will be
impaired.
Plugs and coupler outlets on connection cables must be made
of rubber, plasticised PVC or other thermoplastic material of
same mechanical stability or be covered with this material.
The connector of the connection cable must be splash-proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician or
one of our customer service points. Local regulations –
especially regarding protective measures –
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts. Accidents can arise for the
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury resulting
from such action.
T
r
a
n
s
p
o
r
t
I
n
s
t
r
u
T
r
a
n
s
p
o
r
t
I
n
s
t
r
u
Move the splitting blade right down every time before the
machine is transported.
To
transport
the
machine,
grasp
the
handle and tilt the log
splitter slightly towards
you. The log splitter can
be easily transported in
this position.
Make sure that the oil
tank cap is securely
tightened to prevent oil
from
leaking
during
transport.
c
t
i
o
n
s
c
t
i
o
n
s
transport belt
P
o
s
i
t
i
P
o
s
i
t
i
Ensure that the working area meets the following conditions:
−
no danger of slipping
−
level
−
free of obstacles
−
sufficiently well lit
Do not operate the machine in the direct vicinity of gas
or petrol pipes or containers, or any other easily inflammable
materials.
S
t
a
r
t
-
S
t
a
r
t
-
Check that the machine is completely and correctly
assembled.
Before using the log splitter, make sure each time that
there are no faulty connections (tears, cuts, etc.)
−
there are no damages at the machine
−
all screws are tight
−
check the hydraulic system for any possible leaks
−
the oil level
−
dipstick before start up the machine.
Transport closure
must be
Oil dipstick
If the hydraulic system is not vented, the trapped air will
damage the seals and cause permanent damage to the log
splitter.
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to the
relevant and properly earthed plug.
Only use connection cables with sufficient cross-sections.
Connect the machine via a 30 mA fault current safety switch.
Fuse protection
o
n
i
n
g
o
n
i
n
g
u
p
u
p
Do not use defective power supply cables.
The transport closure must be replaced by the oil
400 V 3~
16 A
25
Werbung
Kapitel
Inhaltsverzeichnis
