Cleaning, Maintenance And Ordering Of Spare Parts; Disposal And Recycling - EINHELL BT-LS 1014 D Bedienungsanleitung

Anleitung_BG_CS_85_E_SPK1:_
6.2 Set the grinding angle according to the
specifications for your chain (Fig. 8) (normally
between 30-35º)
Slacken the locking screw for setting the grinding
angle (1)
Set the desired grinding angle using the scale (2)
Tighten the locking screw (1) again
6.3 Set the chain stopper (Fig. 9/10)
Fold the chain stopper (1) onto the chain
Pull the chain backwards against the chain
stopper (1) until the latter stops a cutting link (2)
Important! You must make sure that the angle
of the stopped cutting link coincides with the
grinding angle. If it does not, pull the chain one
link further.
Fold the grinding head (4) down until the grinding
wheel (5) is touching the chain link (6) that is to
be ground. (To do so, you can move the chain
back and forth a little using the setting screw of
the chain stopper (3)
6.4 Set the depth limit (Fig. 10)
Fold the grinding head (4) down and set the
grinding depth using the setting screw (7)
Important! The grinding depth should be set so
that the full cutting edge of the cutting link is
sharpened.
6.5 Lock the chain (Fig. 7)
Tighten the chain locking screw (1)
6.6 Grind the link (Fig. 10/11)
Switch the appliance on at the ON/OFF switch
(1)
Carefully bring the grinding wheel (5) with
grinding head (4) so that it is against the set link
Switch the appliance off at the ON/OFF switch
(1)
Every second link in the chain must be sharpened in
this way. To know when every second link in the
entire chain has been sharpened, mark the first link
(e.g. with chalk). Once all cutting links on one side
have been sharpened, the grinding angle must be
set to the same number of degrees on the other side.
You can then begin to sharpen the links of the other
side(without having to make any further
adjustments).
6.7 Set the depth limiter spacing (Fig. 12/13)
Once the chain has been fully sharpened, you must
make sure that the depth limiter spacing is kept (the
depth limiters (1) must be lower than the cutting links
(2). You may need to file the depth limiters (1) to the
specifications for your chain using a file (3) (not
05.06.2008 14:21 Uhr Seite 11
included in delivery).
7. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible. Wipe
the equipment with a clean cloth or blow it with
compressed air at low pressure.
We recommend that you clean the tool immediately
after you use it.
Clean the equipment regularly with a moist cloth and
some soft soap. Do not use cleaning agents or
solvents; these may be aggressive to the toolʼs
plastic parts. Ensure that no water can get into the
interior of the tool.
7.2 Changing the grinding wheel
Important! Always switch the appliance off and
unplug the power plug before carrying out any
maintenance.
1. Remove the grinding wheel (Figs. 14-16)
2. Fit a new grinding wheel
3. Assemble in reverse order
Do not use grinding wheels that are worn, broken,
cracked or otherwise damaged.
Use only genuine grinding wheels.
7.3 Ordering replacement parts
Please provide the following information on all orders
for spare parts:
Model/type of tool
Article number of the tool
ID number of the tool
Number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
GB
11