Prior To Operation - DeWalt D26411 Bedienungsanleitung


WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.

WARNING: Do not place your other hand over the air
vents (Fig. C).
Proper hand position requires one hand holding the tool as
shown in Figure B.

Prior to Operation

1. Attach the correct accessory recommended for
the application.
2. Turn the air temperature adjustment knob/LCD air
temperature indicator and adjuster
air temperature.
Switching On and Off (Fig. D)
1. Push the on/off switch 1 to the desired air flow settings:
I: 240 liter/min (50 °C–400 °C)
250 liter/min (50 °C–400 °C) (D26414)
A low air flow to heat up the workpiece slowly.
II: 450 liter/min (50 °C–600 °C)
500 liter/min (50 °C–600 °C) (D26414)
A high air flow to heat up the workpiece quickly.
2. To turn the tool off, push the on/off switch
Disconnect the tool from the power source and let the tool
cool down before moving or storing it.
Removing Paint

WARNING: Refer to Important Notice under additional
safety Instructions for Heat guns before using the
tool to remove paint.

WARNING: Do not strip metal window frames as the heat
may crack the glass.
• When striping other window frames, use a glass
protection nozzle.
• To prevent igniting the surface, do not keep the tool
directed at one spot too long.
• Avoid collecting paint on the scraper accessory, as it
may ignite. If necessary, carefully remove paint debris
from the scraper accessory using a knife.
1. Attach the appropriate accessory.
2. Turn the air temperature adjustment knob/LCD air
temperature indicator and adjuster
3. Turn the tool on by selecting the desired air flow.
4. Direct the hot air onto the paint to be removed.
Best results will be achieved if the heat gun is moved slowly,
but CONSTANTLY, from side to side to evenly distribute
heat. DO NOT LINGER OR PAUSE IN ONE SPOT.
5. When the paint softens, scrape the paint away using a
hand scraper.
REMEMBER: Splinters and small particles of stripped paint can
be ignited and blown through holes and cracks in the surface
being stripped.
Stationary Use (Fig. A)
This tool can also be used in stationary mode.
Constant Heat Control (Overload Protection)
When the tool is overloaded, this feature protects the heating
element from damage without stopping the tool and/or
4 to desired
without a cool down period.
Tool Ring (Fig. A)

1 to position O.
For easy storage, the tool can hang from the tool ring
heat gun should be stored indoors.
Cool Down Period
The nozzle and accessory becomes very hot during use. Turn
heat gun off, disconnect from the power source and let the tool
cool down for at least 30 minutes before moving or storing it.
nOtE: To reduce the cooling time, switch the tool on at the
lowest air temperature setting and let it run for a few minutes
before turning the heat gun off.
MAINTENANCE
Your D
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

to high.
4
Lubrication
Your power tool requires no additional lubrication.
1. Fold down the kickstand 3
2. Set the tool onto a level, stable workbench. Ensure the tool
will not tip over.
3. Secure the power cord to prevent entanglement or pulling
the tool off the workbench.
4. Turn the tool on by selecting the desired air flow.
1. When the temperature gets too hot, the heating element
switches itself off. The motor will continue to run and
produce cold air.
2. When the temperature has cooled sufficiently (taking
only a few seconds) the heating element will switch
on automatically.
WARNING: ALWAYS turn heat gun off, disconnect from
the power source and let the tool cool down for at least 30
minutes before moving or storing it.
WALT power tool has been designed to operate
e
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
EngLIsH
as shown in Figure A.
6 . The
23