Electrical Connection; Cleaning And Maintenance - Scheppach SC36 Originalbetriebsanleitung

Danger!
The roller rotates for a few seconds after the motor is
switched off . Never attempt to stop the roller. In the
event that the rotating roller strikes an object, imme-
diately switch off the equipment and wait for the roller
to come to a complete stop.
Then inspect the condition of the roller. Replace any
parts that are damaged. Lay the power cable on the
ground in loops in front of the power outlet. Scarify
away from the power outlet and cable, making sure
that the power cable always trails in the already scari-
fied grass so that the equipment does not travel over
the cable.

Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer's mains connection as well as the ex-
tension cable used must also comply with these
regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F".
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate
20 GB

Cleaning and maintenance

Danger!
Always pull out the mains power plug before starting
any cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents or
solvents; these could attack the plastic parts of the
equipment. Ensure that no water can seep into the
device. The ingress of water into an electric tool
increases the risk of an electric shock.
Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Danger! The carbon brushes should not be replaced
by anyone but a qualified electrician.
Maintenance
• A worn out or damaged cutting unit should be re-
placed by an authorised expert.
• Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you can
work safely with the scarifier.
• Store the scarifier in a dry place.
• For longer life, all screw-fastened parts, such as
wheels and axles should be cleaned and subse-
quently oiled.
• Regular servicing of the scarifier not only secures
longer endurance and performance, but also con-
tributes to an accurate and simple scarification of
your lawn.
• At the end of the season, carry out a general check
of the scarifier, and remove all residue collected.
Before the start of every season, it is absolutely
necessary to check the state of the scarifier. Con-
tact our Customer Service if repair work is nec-
essary.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the
following parts are therefore also required for use
as consumables.
Wear parts*: Aerator roller, Carbon brushes
* Not necessarily included in the scope of delivery!