Surround; Main Unit - Denon AVC-A1SR Bedienungsanleitung

When connected as shown on the diagram below using connection cords included with Denon power
amplifiers, the power amplifier's power can be turned on and off using the "M-ZONE1 ON/OFF" button on
the remote control unit.
OUT
AC IN
SURR.-B
L
S-VIDEO
IN OUT OUT
SB
MULTI
AUDIO
IN OUT IN L
DBS / CDR / MD /
CD DVD VDP TV SAT V. AUX VCR-1 VCR-2 VCR-3 VCR-1 VCR-2 VCR-3 TAPE-1 TAPE-2
SPEAKER IMPEDANCE
L L
FRONT, CENTER, SURROUND BACK
/ 6 16Ω

SURROUND

A OR B / 6 16Ω
A + B / 8 16Ω
R R
SPEAKER SYSTEMS Power amplifier (Option)
SURR. SURR. SURR. CDR / MD / MULTI ZONE
TUNER FRONT CENTER SURR. BACK FRONT CENTER SURR. BACK FRONT CENTER SURR. BACK TAPE-1 TAPE-2 1 2 AC OUTLETS
AC 230V 50Hz
L
SWITCHED 100W MAX.
R
SW SW SW
IN EXT. IN-1 EXT. IN-2 PRE OUT OUT PREOUT OUT
OUT
GITAL RF IN
DENON
LINK
1 2 3 4 5
EXT. IN
ROOM TO ROOM POWER AMP
COAXIAL 1 2 3 4 5 6 5 6
(REMOTE CONTROL) CONTROL OUT
IN OUT RS-232C OPTICAL
TRIGGER OUT
DC 12V 20mA MAX.
DIGITAL
[2] Multi-zone playback using the MULTI ZONE2 terminals
The AVC-A1SR is equipped with audio pre output terminals with a fixed output level (M-ZONE2) as the
MULTI ZONE2 output terminals. (These are not video outputs.)
Settings can be made at the system setup menu so that the same source as the M-ZONE2 pre-out terminals
can be played from the speakers connected to the M-ZONE2 speaker terminals.
2 When using the PRE OUT terminals
ANOTHER ROOM MAIN ROOM
B
INTEGRATED
AMPLIFIER
RC-871
2 When using the M-ZONE2 (MULTI) speaker terminals
ANOTHER ROOM MAIN ROOM
RC-871
NOTE:
When the main unit is set to the recording output mode, the M-ZONE2 remote control unit key cannot be
operated. (See page 22.)
REMOTE
(ON-OFF)
AVC-A1SR
AVC-A1SR
10 SURROUND
Before playing with the surround function
• Before playing with the surround function, be sure to use the test tones to adjust the playback level from the
different speakers. This adjustment can be performed with the system setup (see page 13) or from the remote
control unit, as described below.
• Adjusting with the remote control unit using the test tones is only possible in the "Auto" mode and only
effective in the DOLBY SURROUND and HOME THX CINEMA modes. The adjusted levels for the different
modes are automatically stored in the memory.
2
1
Press the TEST TONE button.
• After adjusting using the test tones, make the desired settings for each surround mode to be played, then use
the procedure described below to adjust the levels of the various channels.
1

MAIN UNIT:

MODE
SELECT
Press the MODE SELECT button
and select "CH VOL".
The setting mode switches in the
following order each time the
(Main unit)
button is pressed:
SURR. TONE
CH. VOL.
PARAMETER
CONTROL
REMOTE CONTROL UNIT:
Press the CH. SELECT button on
the "SURROUND 2/5" page.
"CH VOL" is selected. (Remote control unit)
2 MAIN UNIT:
FUNCTION
Use the FUNCTION knob to
select the speaker whose
level is to be adjusted.
(Main unit)
REMOTE CONTROL UNIT:
Press the CURSOR/PAGE button on the
"SURROUND 2/5" page to highlight the
display, then press jog stick "ENTER". The
channel (speaker) switches as shown on the
diagram below each time it is pressed.
(Remote control unit)
2
Test tones are output from the different
speakers. Press the CURSOR/PAGE button to
highlight the display, then use the jog stick to
adjust the channel level.
1, 3
2, 3
3
After completing the adjustment, press the
CURSOR/PAGE button again so that the display
is no longer highlighted, then press the TEST
TONE button to complete the operation.
1 2 3
2, 3
FL C FR SR SBR
SW
FADER
ENGLISH
1, 4
2, 4
SBL
SL
25