Denon AVC-A1SR Bedienungsanleitung Seite 10

ENGLISH
NOTES:
• The on-screen display signals are output with priority to the S-VIDEO input jack during playback of a video
component. For example, if the TV monitor is connected to both the AVC-A1SR's S-Video and video
monitor output jacks and signals are input to the AVC-A1SR from a video source (VDP, etc.) connected to
both the S-Video and video input jacks, the on-screen display signals are output with priority to the S-Video
monitor output. If you wish to output the signals to the video monitor output jack, do not connect a cord
to the S-VIDEO INPUT jack. (For details, see page 19.)
• The AVC-A1SR's on-screen display function is designed for use with high resolution monitor TVs, so it may
be difficult to read small characters on TVs with small screens or low resolutions.
• The setup menu is not displayed when headphones are being used.
• Speaker system layout
Basic system layout (For a THX Surround EX system)
• The following is an example of the basic layout for a system consisting of eight speaker systems and a
television monitor:
Subwoofer
Front speaker systems
Set these at the sides of the TV or screen with
their front surfaces as flush with the front of
the screen as possible.
Two surround back speakers are required to use the THX Ultra2 Cinema and THX Music modes.
Set the surround back speakers so that the distance to the listening point is the same for both the left and right
speakers. It is also recommended that the deviations of the distance from the listening position to L and R
channel speakers (front left (FL) and front right (FR), surround left (SL) and surround right (SR), surround back left
(SBL) and surround back right (SBR)) is less than 2 ft (60 cm).
With the AVC-A1SR it is also possible to use the surround speaker selector function to choose the best layout
for a variety of sources and surround modes.
A A A
B B B
SB SB
Using A only
(Multi surround speaker system) (Single surround speaker system)
(SB: Surround Back Speakers)
10
Center speaker system
Surround back speaker systems
Surround speaker systems
• Surround speaker selector function
This function makes it possible to achieve the
optimum sound fields for different sources
by switching between two systems of
surround speakers (A and B). The settings of
the different speakers (A only, B only or A+B)
A
are stored in the memory for the different
surround modes, so
automatically when the surround mode is
selected.
B
SB SB
Using B only
Before setting up the system
1
Check that all the connections
¢ ON / STANDBY
are correct, then turn on the
main unit's power.
£ OFF
(Main unit)
2
Either lightly press on the remote control unit's
touch panel or press the LIGHT button to turn
on the liquid crystal display. (The back light
does not turn on when the touch panel is
pressed.)
3
By default the liquid crystal display is set to
display for 30 seconds, but this can be changed
to approximately 120 seconds using the
procedure described below so that operations
during system up can be performed securely.
4
Lightly press the remote control
unit's jog stick (PUSH ENTER)
to display the icon display
section.
5
Press the "
section to display the "SETUP" icon.
6
Press the "SETUP" icon for at least 3 seconds
to display the setup screen.
7
Push the remote control unit's
jog stick to the right to display
the "SETUP 4/4" page.
they are set
1
4, 7, 8
8
Press the "
section to display the "AVAMP" icon.
Press the "AVAMP" icon to display the page
section.
" button in the icon display
Press "SYSTEM SETUP" at the bottom left to
display the "System Setup Menu" on the TV
screen.
Press the "LCD 30s"
button on this page so
that this part is
displayed in half-tone
dot mesh.
Now press the "•"
button to set the time
display to "120".
2, 5, 6, 7, 8
2
" button in the icon display
Push the remote control unit's
jog stick to the right to display
the "SETUP 3/5" page.