Use And Maintenance; Cleaning And Maintenance; List Of Spare Parts - Baron 700 Serie Aufstellung, Gebrauchs- Und Instandhaltungs Anweisungen

Data Emissione 26/10/2004
measurement while the equipment is operating. The measured
value must be included within the limits indicated in the T4 table;
otherwise, stop the test and call the gas service company.
Disconnect the pipe of the pressure gage and screw down the
screw of the pipe tap tightly.
5 - CHECK OF SOME MALFUNCTIONS
5.1 The pilot burners show a difficult ignition or they fail to ignite
Piezoelectric lighter, ignition plug or pilot burner cable faulty.
Insufficient gas feeding pressure. Nozzle or pipe clogged. The gas
cock is faulty.
5.2 Extinction of pilot burner during the operation
The thermocouple is faulty, or it is not properly heated, or not
correctly connected to the gas cock. Gas feeding pressure drop.
The gas cock is faulty.
5.3 The main burners show a difficult ignition or they fail to ignite
Insufficient gas feeding pressure. Nozzles clogged. The gas cock is
faulty.
6 - REPLACING SOME COMPONENTS
N.B.: The sealed components must not be tampered with. After any
operation, check that there are no leaks, if necessary.
6.1 Main burner
Remove the grill, the spaahback, the lava stones and the frame for
the lava stones. Remove the knob and the control board and
substitute the component.
6.2 Pilot burners, gas cock
Remove the knob and the control board. This allows to get the
component concerned with the substitution.
6.3 Thermocouple, piezoelectric lighter, spark plug
Remove the knob and the control board. This allows to get the
component concerned with the substitution.

7 - USE AND MAINTENANCE

7.1 Warning
This equipment has been designed for professional aims, therefore
it must be operated exclusively by trained personnel. It must
exclusively be used to cook food; consequently any other use is
improper. Before using the charcoal grill for the first time, remove
the industrial protection grease washing it with water and alkaline
detergent. Before using the appliance, when it is still cold, empty the
oilcollecting tray every day. Its installation and possible
transformation for other gas group must be carried out by
authorized and qualified installers. In case of troubles, turn off the
gas cutoff cock installed before the equipment. For any repair, call
the authorized After-Sales Service and require only original spare
parts.
USE - Before switching on the charcoal grill, clean all its surfaces in
contact with food, with the utmost care.
ATTENTION!: As far as the lava stone quantity to be used in the grill
is concerned, please look at the T5 table.
Not complying with these instructions may seriously compromise the
safety of this equipment; the manufacturer declines any liability in
case these warnings are not complied with.
7.2 Use of the charcoal grill
The knob controlling the cocks is marked with the following symbols:
Off
Pilot burner on
Maximum fire
Minimum fire
7.3 Lighting the burners
Press and turn the knob to the position
using the button of the piezoelectric lighter. After lighting, keep the
knob pressed for approximately 20 seconds, then release it. In case
of extinction of the pilot burner, repeat this operation. The pilot
burner can be checked through the lava stones.
Turn the knob to the desired position chosen between
7.4 Extinction of burners
- Switch off the main burner turning the knob to the position
-Switch off the pilot burner pressing and turning the knob to the
position .

8 - CLEANING AND MAINTENANCE

Wash the surfaces of stainless steel with water and non abrasive
detergents, every day; then rinse abundantly and wipe. When
cleaning stainless steel, never use detergents with abrasive
substances, chips, steel wool, brushes or scrapers of common steel.
Clean the floor under the appliance with non corrosive products.
Clean every day the flame holes of the burners and remove the
possible encrustations. Do not wash the equipment with water jets.
When the equipment must not be used for long time, comply with
the following instructions:
Turn off the gas cock installed before the equipment. Clean with
accuracy all the stainless steel surfaces and protect them with a thin
layer of white mineral oil which has to be spread with a cloth.
Ventilate the rooms periodically.

9 - LIST OF SPARE PARTS

Gas cook, Pilot burner, Main burners, Thermocouple, Knob, Spark
plug, Piezoelectric lighter
10
Revisione 0.0
and light the pilot burner
and
.