Operation - Makita MLS100 Betriebsanleitung

Press the shaft lock to lock the spindle and use the
wrench to loosen the hex bolt clockwise. Then remove the
hex bolt, outer flange and blade. (Fig. 18)
To install the blade, mount it carefully onto the spindle,
making sure that the direction of the arrow on the surface
of the blade matches the direction of the arrow on the
blade case. Install the outer flange and hex bolt, and then
use the wrench to tighten the hex bolt (left-handed)
securely counterclockwise while pressing the shaft lock.
(Fig. 19 & 20)
CAUTION:
• The ring 25.4 mm or 30 mm in outer diameter is
factory-installed onto the spindle. Before mounting the
blade onto the spindle, always be sure that the correct
ring for the arbor hole of the blade you intend to use is
installed onto the spindle.
Install the outer flange and hex bolt, and then use the
wrench to tighten the hex bolt (left-handed) securely
counterclockwise while pressing the shaft lock.
Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure the
center cover. Lower the handle to make sure that the
blade guard moves properly. Make sure shaft lock has
released spindle before making cut.
Dust bag (Fig. 21 & 22)
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust bag
of its contents, tapping it lightly so as to remove particles
adhering to the insides which might hamper further
collection.
NOTE:
If you connect a Makita vacuum cleaner to your saw,
more efficient and cleaner operations can be performed.
Securing workpiece
WARNING:
• It is extremely important to always secure the
workpiece properly and tightly with the vise. Failure to
do so can cause the tool to be damaged and/or the
workpiece to be destroyed. PERSONAL INJURY MAY
ALSO RESULT. Also, after a cutting operation, DO
NOT raise the blade until the blade has come to a
complete stop.
CAUTION:
• When cutting long workpieces, use supports that are
as high as the top surface level of the turn base. Do not
rely solely on the vertical vise and/or horizontal vise to
secure the workpiece.
• Thin material tends to sag. Support workpiece over its
entire length to avoid blade pinch and possible
KICKBACK. (Fig. 23)
Vertical vise (Fig. 24)
The vertical vise can be installed in two positions on either
the left or right side of the guide fence. Insert the vise rod
into the hole in the guide fence and tighten the screw to
secure the vise rod.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the screw. Make sure that no part of the tool
contacts the vise when lowering the handle all the way. If
some part contacts the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
CAUTION:
• The workpiece must be secured firmly against the turn
base and guide fence with the vise during all
operations.

OPERATION

CAUTION:
• Before use, be sure to release the handle from the
lowered position by pulling the stopper pin.
• Make sure the blade is not contacting the workpiece,
etc. before the switch is turned on.
• Do not apply excessive pressure on the handle when
cutting. Too much force may result in overload of the
motor and/or decreased cutting efficiency. Push down
handle with only as much force as is necessary for
smooth cutting and without significant decrease in
blade speed.
• Gently press down the handle to perform the cut. If the
handle is pressed down with force or if lateral force is
applied, the blade will vibrate and leave a mark (saw
mark) in the workpiece and the precision of the cut will
be impaired.
1. Press cutting (Fig. 25)
Secure the workpiece with the vise. Switch on the tool
without the blade making any contact and wait until
the blade attains full speed before lowering. Then
gently lower the handle to the fully lowered position to
cut the workpiece. When the cut is completed, switch
off the tool and WAIT UNTIL THE BLADE HAS COME
TO A COMPLETE STOP before returning the blade to
its fully elevated position.
2. Miter cutting
Refer to the previously covered "Adjusting the miter
angle".
3. Bevel cut (Fig. 26)
Loosen the knob and tilt the saw blade to set the bevel
angle (Refer to the previously covered "Adjusting the
bevel angle"). Be sure to retighten the knob firmly to
secure the selected bevel angle safely. Secure the
workpiece with a vise. Switch on the tool without the
blade making any contact and wait until the blade
attains full speed. Then gently lower the handle to the
fully lowered position while applying pressure in
parallel with the blade. When the cut is completed,
switch off the tool and WAIT UNTIL THE BLADE HAS
COME TO A COMPLETE STOP before returning the
blade to its fully elevated position.
CAUTION:
• Always be sure that the blade will move down to bevel
direction during a bevel cut. Keep hands out of path of
saw blade.
• During a bevel cut, it may create a condition whereby
the piece cut off will come to rest against the side of the
11