Kärcher SB MU 908 Originalbetriebsanleitung Seite 62

Display Cause
F 001 Electronic outlets overloaded
F 004 Dimming sensor defective
F 005 Protective motor switch on high pressure pumps was triggered
F 006 Connection to RDS defective
F 007 The pressure switch air does not report any pressure
F 010 No connection to pump electronics at washing station 1
F 011 Electronic outlets at washing station 1 overloaded
F 012 Current pickup of high pressure pump at washing station 1 too high
F 013 Current pickup of high pressure pump at washing station 1 too low
F 014 Contact of high pressure pump at washing station 1 stuck
F 015 Semiload valve at washing station 1 defective
F 016 Coiling protection contact of high pressure pump washing station 1 has
triggered.
F 017 Oil level of high pressure pump at washing station 1 too low
F 018 Electronics at washing station 1 defective
F 020 No connection to remote control electronics at washing station 1
F 021 Fault at coin acceptor at washing station 1
F 022
F 030 No connection to pump electronics at washing station 2
F 031 Electronic outlets at washing station 2 overloaded
F 032 Current pickup of high pressure pump at washing station 2 too high Acknowledge the fault. If the fault recurs, call cus-
F 033 Current pickup of high pressure pump at washing station 2 too low
F 034 Contact of high pressure pump at washing station 2 stuck
F 035 Semiload valve at washing station 2 defective
F 036 Coiling protection contact of high pressure pump washing station 2 has
triggered.
F 037 Oil level of high pressure pump at washing station 2 too low
F 038 Electronics at washing station 2 defective
F 040 No connection to remote control electronics at washing station 2
F 041 Fault at coin acceptor at washing station 2
F 042
F 050 No connection to pump electronics at washing station 3
F 051 Electronic outlets at washing station 3 overloaded
F 052 Current pickup of high pressure pump at washing station 3 too high Acknowledge the fault. If the fault recurs, call cus-
F 053 Current pickup of high pressure pump at washing station 3 too low
F 054 Contact of high pressure pump at washing station 3 stuck
F 055 Semiload valve at washing station 3 defective
F 056 Coiling protection contact of high pressure pump washing station 3 has
triggered.
F 057 Oil level of high pressure pump at washing station 3 too low
F 058 Electronics at washing station 3 defective
F 060 No connection to remote control electronics at washing station 3
F 061 Fault at coin acceptor at washing station 3
F 062
F 070 No connection to pump electronics at washing station 4
F 071 Electronic outlets at washing station 4 overloaded
F 072 Current pickup of high pressure pump at washing station 4 too high Acknowledge the fault. If the fault recurs, call cus-
62
Faults shown in the display
25
-
EN
Remedy
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
Call customer service.
Reset motor protection switch; call Customer Ser-
vice if the problem recurs.
Call customer service.
Check the compressor and the compressed air
lines.
Call customer service.
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
See "Faults on high pressure pumps"
Call customer service.
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
Refill oil, acknowledge the fault.
Call customer service.
Check the connector of the data cable with the elec-
tronics of the remote control.
Call customer service.
Check the microswitch on the mechanical coin ac-
ceptor, replace electronic coin acceptor
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
tomer service.
See "Faults on high pressure pumps"
Call customer service.
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
Refill oil, acknowledge the fault.
Call customer service.
Check the connector of the data cable with the elec-
tronics of the remote control.
Call customer service.
Check the microswitch on the mechanical coin ac-
ceptor, replace electronic coin acceptor
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
tomer service.
See "Faults on high pressure pumps"
Call customer service.
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
Refill oil, acknowledge the fault.
Call customer service.
Check the connector of the data cable with the elec-
tronics of the remote control.
Call customer service.
Check the microswitch on the mechanical coin ac-
ceptor, replace electronic coin acceptor
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
tomer service.