User's Responsibility; Safety Standards - Gianni Ferrari GTR160 Technisches Handbuch

5. USER'S RESPONSIBILITY

It is imperative that the user reads through this manual carefully so as to become acquainted with its working
procedure, maintenance of parts and proper lubrication according to our instructions.The user is also responsible
for checking, repairing and for possible replacement of wornout parts which could cause injuries.The user is re-
sponsible for damages caused to third parties by improper use. The machine must be used and maintained only
by persons with a good knowledge of its specific features and who have fully understood the safety rules.
Never let children or minors near the machine. Local laws, if any, may state a minimum age for the operator. Never
take passengers. Only factory approved attachments and accessories are permitted.
It is strictly prohibited to do any alterations or reconstructions to the machine which are not mentioned in this
manual.
WHEN USING THE MACHINE, THE OPERATOR MUST SCRUPULOUSLY OBSERVE THE SAFETY RULES CONTAINED IN
THIS MANUAL, THE RULES FOR THE PREVENTION OF ACCIDENTS, OTHER GENERAL SAFETY RULES, THE PROVISIONS
OF WORK MEDICINE.

6. SAFETY STANDARDS

ONLY A CAREFUL USER IS A GOOD USER
If you follow the Safety Instructions in the manual you can avoid accidents.
MAIN PART
1) Read through carefully each section of these instructions.
2) Check the machine before every use for defect, for e.g. loose screws and bolts, loosened or damaged blades
or other parts which are not secure. It is absolutely forbidden to use the machine in improper conditions.
Therefore, before starting your machine go through the control and service instructions as recommended.
3) Before starting the machine acquaint yourself with all the parts and with the checking system.
4) The machine should only be used by adults with experience. Don't let children use it.
Avoid using the machine if you do not feel physically fit for the job.
5) Keep people within a certain security distance as explained hereafter.
6 Only use original parts and accessories. Do not make any changes thereto.
For information, please consult your dealer.
7) Replace lost or damaged safety stickers or warning labels. Chek the list of safety stickers in the "SAFETY
PRE CAUTIONS" section of this manual. Wipe dust and dirt off the stickers.
8) Keep hands and feet, as well as your body away from the moving parts.
9) Never use the machine without protection and covers in the right position and perfect condition.
Do not use the machine if its safety devices are not perfectly efficient.
For no reason, tamper with the machine safety devices.
10) Should an object have been run over or got stuck, stop immediately. Turn off the engine and remove the
ignition key. Disengage the P.T.O., put the attachment onto the ground and inspect it. Do not start using the
machine until you are sure that it is in perfect working order.
11) When you have finished working with the machine, disengage the P.T.O.*, put the attachment lower down
so that it touches the ground, turn off the engine and remove the key.
12) Before carrying out maintenance operations on the machine make sure that the same is off.
Before intervening on the electrical installation, disconnect the power cables from the battery terminals.
13) Machine speed should be suited to the ground you are working on.
14) Working on slopes requires extreme caution and reduced speed.
15) When using the machine wear suitable clothing, glasses, gloves and any other protective clothing.
16) Only use the machine with good visibility.
17) All drivers should receive a professional and practical training. Such training should highlight the following:
- the necessity of paying attention and being concentrated when working on machines where the driver is sitting.
- a machine sliding down a slope can be brought again under control by pulling the brakes. The main causes
for the loss of control are:
a) insufficient grip of the wheels;
b) driving too fast;
c) inadequate braking;
d) type of machine unsuitable for the job required;
e) lack of awareness of the effect of the condition of the ground, particularly of slopes ;
f) the equipments are wrongly attached and the loads are consequently badly distributed.
18) During the phases of work, always wear strong shoes and long trousers. Do not use the machine when you
are bare-footed or wearing sandals.
19) Inspect thoroughly the area where the machine is to be used and remove all the object that could be thrown
by the machine.
18