Applications; Selecting And Mounting The Lens; Mounting The Camera; Connecting The Camera - Monacor Tvccd-800Col Bedienungsanleitung

age will be accepted if the camera is used for other
purposes than originally intended, if it is not correct-
ly installed or not repaired in an expert way.
G
Important for U.K. Customers!
The wires in this mains lead are coloured in accord -
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the ter minals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be connec-
ted to the terminal which is marked with the letter
N or coloured black.
3. The wire which is coloured brown must be con -
nected to the terminal which is marked with the
letter L or coloured red.
Warning - This appliance must be earthed.
If the camera is to be put out of operation
definitively, take it to a local recycling plant for
a disposal which is not harmful to the envi-
ronment.

3 Applications

The high-resolution colour camera TVCCD-800COL
has especially been designed for application in CCTV
surveillance systems. Due to the wide dynamic featu-
re it is possible to recognize the faces of persons even
at unfavourable backlight, e. g. in front of a bright wind-
ow. With low illumination the camera switches to B/W
re production (night operation).
Due to the versatile adjusting facilities via an on-
screen menu the camera can be adapted in an opti-
mum way to the respective application range.

4 Selecting and Mounting the Lens

A lens with CS mount thread must be used for the
TVCCD-800COL. It is possible to use both a lens with
automatic iris control [AI lens ("auto iris"), video signal
controlled or DC controlled] and a lens with manual iris
adjustment.
CAUTION
G
Protect the CCD image sensor and the lenses of the
lens assembly against dust and impurities and never
touch them with your fingers. If no lens is screwed on,
always place the protective cover on the lens support
of the camera to protect the CCD image sensor.
G
To prevent damage to the camera or lens, prior to
connecting a lens check the position of the selector
switch (1) for the lens type and the pin configura tion
of the connecting plug of the lens.
1) Remove the protective cover and screw the lens to
the camera.
2) When using an AI lens, set the selector switch (1)
to the lens type used:
VIDEO for a video signal controlled lens
DC for a DC controlled lens
Connect the lens to the 4-pole jack (10). If re -
quired, used the supplied plug. Depending on the
position of the selector switch (1) the jack has the
following pin configuration:
2 1
4 3
Fig. 8 Connecting jack of the lens
Pin Position DC
1 damp -
2 damp +
3 drive +
4 drive -

5 Mounting the Camera

The camera may be mounted to a camera support (e. g.
support of the MONACOR TVH series), to a camera
stand, or to a pan/tilt head (e. g. MONACOR VPT-50).
For fixing, the camera is equipped on its lower side
with an adapter base (7) with two threaded jacks
[thread 6.3 mm ( 1 / ")]. This base can also be screwed
4
to the upper side of the camera for suspended mount -
ing. In case of outdoor mounting insert the camera into
a weatherproof housing in any case.

6 Connecting the Camera

1) Connect the BNC jack VIDEO OUT (9) via a 75 Ω
cable (e. g. MONACOR BNC-1000) to the video
input of the following unit (e. g. monitor, camera
switcher, video splitter). With a cable length ex cee-
ding 100 m a video amplifier should be inserted
between camera and cable to compensate level
loss by the cable.
2) Via the RS-485 interface it is possible to make the
menu adjustments of the camera from a computer
or a control panel. The camera may be controlled
according to the PELCO-P or PELCO-D protocol
(see chapter 7.3). For this purpose connect the
jack RJ-45 (5):
RJ-45
8 Fig. 9 Interface jack RJ-45
1
Connect pin 1 (signal +) and pin 2 (signal -) to the
corresponding contacts at the control panel. Con-
nect the screening to pin 7 (ground). The pins 4 to
6 are intended for switching between day mode
and night mode by remote control (see chapter
7.1.1, menu item D/N MODE). The other pins are
not connected.
Note: The use of twisted cables will reduce
interference.
3) Connect the plug of the mains cable (6) to a socket
(90 – 260 V~/50 Hz). Thus, the camera is switched
on and the POWER LED (8) lights up.
Position VIDEO
power supply +12 V
not connected
output video signal
ground
GB
13