EINHELL KGST 210/1 Bedienungsanleitung Seite 17

Anleitung KGST 210-1_SPK1:Anleitung KGST 210/1
which conform with EN 847-1: 1997.
Faulty saw blades have to be replaced
immediately.
Never use saw blades which do not comply with
the data specified in this manual.
Make sure that the arrow on the saw blade
complies with the arrow marked on the machine.
Make certain that the saw blade does not touch
the rotary table in any setting. To do so, pull out
the power plug and tilt the saw blade by hand into
the 45° position and the 90° position. If
necessary, re-adjust the saw head as described
in Section C/F.
It is imperative to make sure that all the devices
used to cover the saw blade are in good working
order.
Never wedge the hinged guard hood in open
position.
Never dismantle the machineʼs safety devices or
put them out of operation.
Damaged or faulty safety devices have to be
replaced immediately.
Never cut workpieces which are too small to hold
securely in your hand.
Do not place your hands in awkward positions
where one or both may slip suddenly and touch
the saw blade.
When working with long workpieces, use an
additional support (table, stand, etc.) to prevent
the machine from tipping over.
Always clamp round workpieces such as dowel
rods etc. with suitable devices.
There must be no nails or other foreign bodies in
that part of the workpiece you want to cut.
Always stand to the side of the saw blade when
working with the saw.
Never load the machine so much that it cuts out.
Always press the workpiece firmly against the
table and the stop rail to prevent it from wobbling
or twisting.
Make sure that off-cuts can be removed from the
side of the saw blade. If not, they may catch on
the saw blade crown and be catapulted into the
surrounding area.
Never saw several workpieces simultaneously.
Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
To rectify faults or remove jammed pieces of
wood, always switch off the machine first.
- Pull out the power plug! -
Conversions, adjustments, measurements and
cleaning jobs are to be performed only when the
motor is switched off. - Pull out the power plug! -
Before you switch on the machine, check that all
wrenches and adjustment tools have been
removed.
08.12.2006
GB
When you leave your workplace, switch off the
motor and pull out the power plug.
Electric installation work, repairs and
maintenance are to be carried out only by
specialists.
All guards and safety devices have to be refitted
immediately after completion of any repairs or
maintenance.
It is imperative to observe the manufacturerʼs
safety, operating and maintenance instructions
as well as the dimensions quoted in the technical
data.
It is imperative to observe the accident
prevention regulations in force in your area as
well as all other generally recognized rules of
safety.
Note the information published by your
professional associations.
Switch on the dust extraction system each time
you use the machine.
The machine may be used in closed rooms only
in conjunction with a suitable vacuum extraction
system.
The cross-cut saw must be connected to a 230 V
socket-outlet with a minimum 10 A fuse.
Never use light-duty machines for heavy-duty
work.
Never use the cable for any purpose other than
that for which it is intended!
Adopt a firm standing position and keep your
balance at all times.
Check the tool for signs of damage!
Before you carry on using the tool it is imperative
to check that its safety devices and any slightly
damaged parts are working properly and in the
way intended.
Check that the moving parts work properly and
do not jam or whether any of the parts are
damaged. All parts must be fitted correctly and
satisfy all conditions for the tool to work properly.
Unless otherwise stated in these instructions,
damaged safety devices and parts must be
repaired or replaced by experts in an approved
specialist workshop.
Have damaged switches replaced by a customer
service workshop.
This tool complies with the pertinent safety
regulations. Repairs are to be carried out only by
qualified electricians using original replacement
parts. The user may suffer an accident if this
condition is not observed.
Be careful when working in vertical mode.
Caution! Special care is required when making
double mitre cuts.
Do not overload your tool!
14:23 Uhr Seite 17
17