Before The First Use; Cleaning And Maintenance; Product Warranty - Redmond RMG-1208-E Bedienungsanleitung

I. BEFORE THE FIRST USE
Carefully remove the unit and its accessories from the packaging. Dispose all
packaging materials and promotional stickers.
Keep all warning labels, warning stickers (if any), and the serial number
identification label located on the housing. The absence of the serial number
will deprive you of your warranty benefits!
After transportation or storage at low temperatures allow the appliance to
stay at room temperature for at least 2 hours before using.
Wipe the motor unit with a moist cloth. Wash all removable parts, strictly fol-
lowing the instructions in «Cleaning and maintenance». All the removable parts
should completely dry at room temperature before the assemblage. Ensure that
outer and inner visible parts of the grinder do not have faults, splits and other
defects.
II. OPERATION
The multipurpose meat grinder REDMOND RMG-1208-E is a multifunctional
appliance for food processing.
The meat grinder is equipped with an overload protection system of the motor
(e. g. if the bone gets into the grinder unit together with meat).
If the motor is unexpectedly stopped, press the ON/OFF button, unplug the
appliance and let it cool down for 30 minutes. Clean the loading tray from
remnants and plug in the appliance. The appliance is ready for operation.
CAUTION! The operation time should not exceed 5 minutes. A break should
not be less than 15 minutes.
Ground Meat Making
Prepare the food. Defrost meat and fish, remove bones and sinews. Cut the meat
in 20×20×40 mm pieces so that they pass freely through the feed chute port.
Insert the screw into the meat grinder unit. Carefully put the blade on the screw
with the flat surface out towards the perforated disc. Put the perforated disc on
the screw. The recess on the edge of the disc should fit the cog on the unit.
Put the retaining ring onto the meat grinder unit and turn it clockwise. Do not
apply excessive force.
Turn the assembled block clockwise to 45° and insert its shaft into the junction
box on the housing of the appliance. Turn the retaining ring until
it is tight.
Place the feed chute onto the meat grinder unit.
Put the pieces into the feed chute. Place a bowl for ground meat under the unit
retaining ring.
You are not advised to put bones, animal skin, frozen meat or large chunks of
meat into the feed chute as it reduces the service life of the appliance and
may cause a breakdown.
Plug in the appliance. Then switch on the device pressing the ON/OFF button.
Use the cylindrical pusher to push meat pieces into the feed chute port.
Switch off the appliance pressing the ON/OFF button and unplug it.
Sausage Making
Prepare sausage ground meat. Soak the sausage casing in lukewarm water for
20 minutes.
Insert the meat grinder screw into the meat grinder unit.
Put the sausage attachment base onto the screw. A recess on the edge of the
attachment should fit the cog on the unit wall. Place the sausage attachment
on.
Put the retaining ring onto the meat grinder unit atop the attachment and turn
it clockwise. Do not apply excessive force.
Turn the assembled block clockwise to 45° and insert its shaft into the junction
box on the motor unit. Turn the block counterclockwise until it clicks into place.
Turn the retaining ring until it is tight.
6
Place the feed chute onto the meat grinder unit.
Put the ground meat into the feed chute. Place a flat bowl under the sausage
attachment.
Plug in the appliance.
Tie an end of the casing and put it onto the sausage attachment. The knot
should be 1-2 cm away from the outlet port so that the ground meat would
stuff the casing tight.
Should the casing get stuck to the neck of the attachment, then wet it with
water.
Switch on the appliance by pressing the ON/OFF button.
Use the dismountable pusher to push the ground meat into the feed chute port.
Take the casing off the attachment once it has been stuffed with the ground
meat. Leave some casing to make a knot.
Once the casing has been stuffed, switch off the appliance by pressing the ON/
OFF button. Tie the loose end of the sausage. Then unplug the
device.
Stuffed Sausage (Kebbe) Making
Prepare ground meat for both kebbe outer layer and stuffing.
Insert the screw into the meat grinder unit.
Put the kebbe attachment base onto the screw, and then put the kebbe attach-
ment onto the base.
Put the retaining ring onto the meat grinder unit atop the attachment and turn
it clockwise. Do not apply excessive force.
Turn the assembled block clockwise to 45° and insert its shaft into a junction
box on the motor unit. Turn the block counterclockwise until it clicks into place.
Turn the retaining ring until tight.
Place the feed chute onto the meat grinder unit.
Put the ground meat to make kebbe outer layer into the feed chute. Place a flat
bowl under the kebbe attachment.
Plug in the appliance.
Switch on the device by pressing the ON/OFF button.
Use the dismountable pusher to push ground meat into the feed chute port. A
hollow sausage will come out of the cone attachment. Crimp its end.
Switch off the device by pressing the ON/OFF button when the sausage is of
required length. Cut off the sausage with a knife by the kebbe attachment.
Stuff the sausage with the prepared filling, crimp its end and form the kebbe
the way you like.
Unplug the appliance once you have finished making kebbe.
Use of Reverse Function
Use the reverse function in case you see there is much juice left in the cutting
block or squeezer unit and a dense cake of food has blocked the outlet
port.
If the squeezer is in operation at the moment, stop the rotation of the shaft by
pressing the ON/OFF button. Then press and hold down the REV button. The
screw will turn backwards moving the foods towards the feed chute port. Release
the REV button in 10-15 seconds and then press the ON/OFF button to resume
processing.
III. CLEANING AND MAINTENANCE
Clean all the attachments and parts of the squeezer right after
use.
CAUTION! Switch off the appliance and unplug it before disassembling and
cleaning.
Disassembling
Take the pusher out of the feed chute port, remove the chute.
Press the detachable unit release button, turn the meat grinder unit to 45°
clockwise and detach it from the motor drive unit.
Turn off the retaining ring on the meat grinder unit, take out the detachable
parts (plastic attachments, perforated disc, blade, screw).
Cleaning
Wipe the motor unit with a damp cloth.
Clean the attachments and other parts with nonabrasive scouring
substances.
Do not clean the parts of the appliance in a dishwasher as they may tarnish
being affected by scouring substances.
Do not exceed maximum temperature of 60°C while cleaning metal parts of
the appliance in a dishwasher.
Let all parts dry at room temperature and natural ventilation.
DO NOT immerse the motor drive unit, plug and power cord in water or keep
in running water.
DO NOT use sponges with hard or abrasive surface, abrasive scouring sub-
stances and solvents (benzine, ethyl acetate and others).
Storage
Store the assembled appliance in a dry, ventilated place away from heating and
direct sunlight.
IV. B E F O R E CO N TACT I N G S E RV I C E
CENTRE
Problem Possible causes Solution
Power cord is not connected to
the appliance and (or) to the Plug in the appliance
outlet
The appliance
Plug in the appliance to the working
does not switch Faulty electrical outlet
outlet
on
Check the voltage supply. In case of its
Power supply failure failure, contact an authorized organiza-
tion
Press ON/OFF, unplug the appliance
M o to r u n i t
and let it cool down for 30 minutes.
stopped during Overload protection activated
Clean the loading tray from remnants
operation
and plug in the appliance
The appliance is overheated Reduce continuous operation time,
An off-odour
during operation increase intervals between switching
appeared dur-
Some parts of the appliance
ing operation
The odour will disappear after few uses
have protective cover
V. PRODUCT WARRANTY
We warrant this product to be free from defects for a period of 2 years from
the date of purchase. If the appliance fails to operate properly within the
warranty period and is found to be defective in material or workmanship,
we will repair or replace it free of charge. This warranty comes into force
only in case an original warranty service coupon with a serial article number
and an accurate impress of the company of the seller proves the purchase
date. This limited warranty does not cover damage caused by the failure to
use this product for its normal purpose or in accordance with the instructions
on the proper use and maintenance of the product, or any kind of repair
works. Do not try to disassemble the appliance and keep all package contents.
This warranty does not cover normal wear of the appliance and its parts
(filters, bulbs, non-stick coating, gaskets, etc.).
The service life and the applicable product warranty period start on the date
of purchase or the date of manufacture (if the purchase date cannot be