Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
I. BEFORE THE FIRST USE
Carefully remove the unit and its accessories from the packaging. Dispose all packaging materials and promotional stickers.
Keep all warning labels, warning stickers (if any), and the serial number identification label located on the housing. The absence of the
serial number will deprive you of your warranty benefits!
After transportation or storage at low temperatures allow the appliance to stay at room temperature for at least 2 hours before using.
Wipe the motor unit with a moist cloth. Wash all removable parts, strictly following the instructions in «Cleaning and maintenance». All
the removable parts should completely dry at room temperature before the assemblage. Ensure that outer and inner visible parts of the
grinder do not have faults, splits and other defects.
II. OPERATION
The multipurpose meat grinder REDMOND RMG-1211-E is a multifunctional appliance for food processing.
The meat grinder is equipped with an overload protection system of the motor (e. g. if the bone gets into the grinder unit to-
gether with meat). If the motor is unexpectedly stopped, switch off the meat grinder, press ON/OFF, and disconnect from the
power outlet. Clean the working unit from foods. Press the overload protection button on the bottom of the appliance, then plug
in the appliance and press ON/OFF. If the meat grinder still doesn't work, apply to the service center.
CAUTION! The operation time should not exceed 5 minutes. A break should not be less than 15 minutes.
You are not advised to put bones, animal skin, frozen meat or large chunks of meat into the feed chute as it reduces the service life of
the appliance and may cause a breakdown.
See the appliance usage procedure on the corresponding schemes:
A2
• making mince —
;
A3
• making sausages —
;
Use of Reverse Function
Use the reverse function if liquid accumulates inside the cutting unit or the meat grinder unit and output product's solid mass
prevents it from flowing.
If the squeezer is in operation at the moment, stop the rotation of the shaft by pressing the ON/OFF button. Then press and hold
down the REV button. The screw will turn backwards moving the foods towards the feed chute port. Release the REV button in
10-15 seconds and then press the ON/OFF button to resume processing.
III. CLEANING AND MAINTENANCE
See the recommended methods of cleaning different appliance parts in the table A5
Clean all the attachments and parts of the squeezer right after use.
CAUTION! Switch off the appliance and unplug it before disassembling and cleaning.
Cleaning
Wipe the motor unit with a damp cloth. Clean the attachments and other parts with nonabrasive scouring substances. Do not clean the
parts of the appliance in a dishwasher as they may tarnish being affected by scouring substances. Do not exceed maximum temperature
of 60°C while cleaning metal parts of the appliance in a dishwasher. Let all parts dry at room temperature and natural ventilation.
DO NOT immerse the motor drive unit, plug and power cord in water or keep in running water.
DO NOT use sponges with hard or abrasive surface, abrasive scouring substances and solvents (benzine, ethyl acetate and others).
Storage
Store the assembled appliance in a dry, ventilated place away from heating and direct sunlight.
IV. BEFORE CONTACTING SERVICE CENTRE
Problem
Possible causes
Power cord is not connected to the appliance and
(or) to the outlet
The appliance does
Faulty electrical outlet
not switch on
Power supply failure
A4
• making kibbeh —
.
.
Solution
Plug in the appliance
Plug in the appliance to the working outlet
Check the voltage supply. In case of its failure, con-
tact an authorized organization
Problem
Possible causes
Motor drive stopped
Overload protection activated
during operation
An off-odour ap-
The appliance is overheated during operation
peared during op-
eration
Some parts of the appliance have protective cover The odour will disappear after few uses
V. PRODUCT WARRANTY
We warrant this product to be free from defects for a period of 2 years from the date of purchase. If the appliance fails to operate
properly within the warranty period and is found to be defective in material or workmanship, we will repair or replace it free of
charge. This warranty comes into force only in case an original warranty service coupon with a serial article number and an ac-
curate impress of the company of the seller proves the purchase date. This limited warranty does not cover damage caused by the
failure to use this product for its normal purpose or in accordance with the instructions on the proper use and maintenance of the
product, or any kind of repair works. Do not try to disassemble the appliance and keep all package contents. This warranty does
not cover normal wear of the appliance and its parts (filters, bulbs, non-stick coating, gaskets, etc.).
The service life and the applicable product warranty period start on the date of purchase or the date of manufacture (if the purchase
date cannot be established).
You can determine the manufacture date by the serial number located on the identification label on the housing of the appliance. The
serial number consists of 13 digits. 6th and 7th digits of the serial number identify the month, 8th digit the year of manufacture.
The service life of the product, established by the manufacturer is 3 years from the date of purchase, provided that the unit is used
and maintained in accordance with the user manual and applicable technical standards.
Environmentally friendly disposal (WEEE)
The packaging, user manual and the device itself shall be taken to the applicable collection point for the recycling of
electrical and electronic equipment. Do not throw away the electronic waste to help protect the environment.
Old appliances must not be disposed with other household waste but must be collected separately. Municipal dis-
posal of recyclable wastes is free of charge. The owners of old appliances are required to bring it to a waste facility
centre. With this little extra effort, you can help to ensure that valuable raw materials are recycled and pollutants are
treated as appropriate.
This appliance is labelled in accordance with European Directive 2012/19/EU — concerning used electrical and electronic appli-
ances (waste electrical and electronic equipment WEEE).
The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.
GBR
RMG-1211-E
Solution
Switch off the meat grinder, press ON/OFF, and
disconnect from the power outlet. Clean the working
unit from foods. Press the overload protection but-
ton on the bottom of the appliance, then plug in the
appliance and press ON/OFF. If the meat grinder
still doesn't work, apply to the service center
Reduce continuous operation time, increase intervals
between switching
9
Werbung
Inhaltsverzeichnis
