Calibration Services; Specifications - WIKA CPH6200-S1 Betriebsanleitung

Hand-Held Pressure Indicator
CPH6200-S1 / CPH6200-S2

7. Calibration services

DKD-certificates - other certificates:
If the instrument requires calibration, we recommend returning it, along with its associ-
ated sensors, to the manufacturer. Only the manufacturer is able to verify the instrument's
basic settings and configuration, and if necessary correct them.

8. Specifications

Input
Pressure range in bar
Overpressure safety in bar 1
Burst pressure in bar
Resolution in mbar
Pressure range in bar
Overpressure safety in bar 35
Burst pressure in bar
Resolution in bar
Type of pressure
Accuracy of the measu-
ring chain
Calibration*
Display
Range of display
Units
CPH6200 Digital Instrument specific details:
Functions via key press
Functions via Menu
Data logger
Interface (serial)
1)
Power supply
Power consumption
Working temperature
Air humidity
Storage temperature
Housing
Weight
EMV- / CE-conformity
1) For the intrinsically safe version, the use of the interface is not permitted within an explosive atmosphere.
*) Calibrated in vertical mounting position with lower pressure connection.
**) Not available for the intrinsically safe version CPH62I0.
{} Items in curved brackets are optional extras at an additional price.
WIKA Operating Instructions Hand-Held Pressure Indicator
1: for CPH6200-S1;
0.1 0.16 0.25 0.4
1.5 2 2
2 2 2.4 2.4
0.1
10 16 25 40
80 50 80
42 96 250 400
0.01
gauge {absolute 0.25 up to 16 bar & vacuum on request}
0.2 % FS +/- 1 digit at reference temperature of 20 °C (optional 0.1 %)
factory calibration certificate (optional: DKD calibration certificate)
large LCD display for display of 2 values and additional information
max. -19999 up to 99999, depending on sensors used
can be selected from the following: mbar, bar, Pa, kPa, MPa, mmHg, inHg, psi
(dependent on range)
Min-, Max-memory, Hold, Tare, Offset-correction, Logger (Start/Stop)
Min-, Max-alarm (acoustic**/visual), Sea-level (barom. air pressure), Power-Off-
Function, measuring rate: 4/sec ("slow"); > 1000/sec ("fast"); > 1000/sec unfil-
tered ("peak-detect") [via "peak-detect" and min-/max-memory: pressure peaks
of 1.5 msec can be detected]
- discrete value-logger: up to 99 data points (incl. time-stamp) via key press
- cyclic-logger: automatic logging of up to 10000 values incl. time.
cycle-time: selectable between 1 ... 3600 seconds
RS-232 or USB interface via special interface cables
9V-zinc-carbon battery, alternative**: 9V rechargeable battery or mains supply
Cycle-time slow: < 1.6 mA, fast: < 7.0 mA, Low-Power-Logger-Fct.: < 0.3 mA
0 ... 50 °C
0 ... 95 % relative humidity without moisture condensation
-20 ... +70 °C
Impact-resistant ABS, membrane keyboard, transparent panels (CPH62I0 with
cover)
Approx. 160 g
The CPH6200 device corresponds to the essential protection requirements estab-
lished in the regulations of the council for the approximation of legislation of the
member countries regarding electromagnetic compatibility (89/336/EWG).
2: for CPH6200-S2
0.6 1.0 1.6 2.5
4 5 10 10
4.8 6 12 12
1
60 100 160 250
120 200 320 500
550 800 1000 1200
0.1
GB
4.0 6.0
17 35
20.5 42
400 600 1000
800 1200 1500
1700 2400 3000
1
23