Yamaha RX-V365 Bedienungsanleitung Seite 37

LFE signals output
Choice Subwoofer Front speakers
BOTH*
Output
SWFR Output
FRONT
No output
Low-frequency signals output
Choice Subwoofer Front speakers
BOTH*
*1
SWFR
*4
FRONT
No output
Notes
*1 Outputs the low-frequency signals of the front channels and other
speakers to "SML" or "NONE."
*2 Always output the low-frequency signals of the front channels.
*3 Output the low-frequency signals if the sizes of speakers are set to
"LARGE" (or "LRG").
*4 Output the low-frequency signals of the speakers set to "SML."
■
CROSSOVER
Crossover
Use this feature to select a crossover frequency of all the
speakers set to "SML" (or "SMALL") or to "NONE" in
"SPEAKER SET" (see pages 31 and 32).
Choices: 40Hz, 60Hz, 80Hz*, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
Note
• All frequencies below the selected frequency will be sent to the
subwoofer or to the speakers set to "LRG" (or "LARGE") in "SPEAKER
SET" (see pages 31 and 32).
■
Subwoofer phase
Use this feature to switch the phase of your subwoofer if
bass sounds are lacking or unclear.
Choice
NRM*
Does not reverse the phase of your subwoofer.
REV
Sets the phase of your subwoofer to reverse.
B)SP LEVEL
Speaker level
Use this feature to manually adjust the output level of each
speaker.
Control range: –10 dB to 0 dB* to +10 dB
Control step: 1 dB
SP LEVEL
FL
Front left speaker
FR
Front right speaker
C
Center speaker
SL
Surround left speaker
SR
Surround right speaker
SWFR
Subwoofer
Other speakers
No output No output
No output No output
Output No output
Other speakers
*2 *3
*3 *3
*1 *3
SWFR PHASE
Function
Adjusted speaker
Notes
• The available speaker channels differ depending on the setting of the
speakers.
• This does not affect recorded material.
C)SP DISTANCE
Speaker distance
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
All sounds would be adjusted to arrive at the listening
position at the same time regardless of distance from each
speaker.
■
UNIT
Unit
Choice
meters* When you adjust speaker distances in meters.
feet
When you adjust speaker distances in feet.
■
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting:
FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)
CENTER: 2.60 m (8.5 ft)
SUR. L/SUR. R: 2.40 m (8.0 ft)
SP DISTANCE
FRONT L
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SUR. L
Surround left speaker
SUR. R
Surround right speaker
SWFR
Subwoofer
Note
• The available speaker channels differ depending on the setting of the
speakers.
Center graphic equalizer
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers.
Control range: –6.0 dB to 0 dB* to +6.0 dB
Control step: 0.5 dB
y
• Press ok / n to select a frequency band and ol / h to adjust the
selected frequency band.
• You can make adjustment while listening to the currently source or a test
tone.
Following is an example where "100Hz" is selected as the
frequency band.
100Hz--||--
Set menu
Condition
Adjusted speaker
D)CENTER GEQ
0
33
En