Explanation Of Symbols And Safety Instructions; Explanation Of Symbols; General Safety Instructions - Buderus AM200 Installationsanleitung Für Den Fachmann

Table of contents
Table of contents
1 Explanation of symbols and safety instructions . . . . . . . . . . 24
1.1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . 24
2 Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.1 System requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.2 Important information on use . . . . . . . . . . . . . . . . . . . . 25
2.3 Function definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.4 Setting the coding card . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.5 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.6 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.7 Additional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.8 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.2 Insulation of the temperature sensor at the buffer
cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.1 Connecting the BUS connection and temperature
sensor (extra-low voltage side) . . . . . . . . . . . . . . . . . . . 27
3.3.2 Connecting the power supply, pump and mixer
(mains voltage side). . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3.3 Connection diagrams with system schematics . . . . . . 28
3.3.4 Overview of the terminal assignment . . . . . . . . . . . . . . 29
4 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.1 Setting the coding card . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.2 System and module commissioning . . . . . . . . . . . . . . . 30
4.3 More status indicators at the module . . . . . . . . . . . . . . 30
4.4 Menu settings of alternative heat source . . . . . . . . . . . 30
4.5 Diagnosis menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.1 Indicator of module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.2 Indicator of alternative heat source. . . . . . . . . . . . . . . . 32
5.3 Indicator of bypass valve/heating circuit pump . . . . . . 32
5.4 Buffer cylinder indicator . . . . . . . . . . . . . . . . . . . . . . . . 32
5.5 Indicator of conventional heat source block. . . . . . . . . 33
5.6 Faults not indicated at the module . . . . . . . . . . . . . . . . 33
6 Overview of the service menu . . . . . . . . . . . . . . . . . . . . . . . . . 33
7 Environmental protection/disposal. . . . . . . . . . . . . . . . . . . . . 33
24
1

Explanation of symbols and safety instructions

1.1

Explanation of symbols

Warnings
In warnings, signal words at the beginning of a warning are used to
indicate the type and seriousness of the ensuing risk if measures for
minimising danger are not taken.
The following signal words are defined and can be used in this document:
DANGER:
DANGER indicates that severe or life-threatening personal injury will
occur.
WARNING:
WARNING indicates that severe to life-threatening personal injury may
occur.
CAUTION:
CAUTION indicates that minor to medium personal injury may occur.
NOTICE:
NOTICE indicates that material damage may occur.
Important information
The info symbol indicates important information where there is no risk to
people or property.
Additional symbols
Symbol Meaning
▶ a step in an action sequence

a reference to a related part in the document
• a list entry
- a list entry (second level)
Table 1
1.2

General safety instructions

H Instructions for the target group
These installation instructions are intended for
registered gas fitters, plumbers, heating engineers
and electricians. All instructions must be observed.
Failure to comply with instructions may result in
material damage and/or personal injury, including
possible loss of life.
▶ Read the installation instructions (heat source,
heating controller, etc.) before installation.
▶ Observe safety instructions and warnings.
▶ Observe national and regional regulations,
technical rules and guidelines.
▶ Keep a record of all work carried out.
AM200 - 6720871012 (2017/06)