Safety Instructions - Sygonix 1359880 Bedienungsanleitung

Operating instructions
GB
DIS Surveillance camera, 1000 TVL,
2.8 - 12 mm
Item no. 1359880
Intended use
This camera is intended for image monitoring and protecting secluded or
critical areas (e.g., entrance areas, surveillance of underground car parks
and the like).
The camera is only intended to be used with a stabilised direct current of
12 V/DC.
The product is designed for use indoors and outdoors (IP65).
Please bear in mind that it is prohibited by law to observe strangers with a
camera without their knowledge and consent. Observe the rules and regu-
lations of the country where you are using the camera.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this pro-
duct and involves the risk of short circuits, fire, electric shock, etc. No part
of the product may be modified or converted!
This product complies with the applicable national and European require-
ments. All names of companies and products are the trademarks of the
respective owners. All rights reserved.
Package contents
• Camera with pre-mounted wall bracket
• Allen key
• Installation material (3 screws, 3 wall screw-plugs)
• Operating instructions
Explanation of symbols
This symbol indicates specific risks associated with handling, func-
tion and use.
The "arrow" symbol indicates special tips and operating information.

Safety instructions

The warranty will be void in the event of damage caused by
failure to observe these safety instructions! We do not assume
any liability for any resulting damage!
We shall not accept liability for damage to property or personal
injury caused by incorrect handling or non-compliance with the
safety instructions. In such cases, the warranty will be null and
void.
• The unauthorised conversion and/or modification of the product
is not permitted for safety and approval reasons (CE). Never dis-
mantle the product.
• The camera is only intended to be used with a stabilised direct cur-
rent of 12 V/DC. The inner contact of the round low-voltage plug
should be plus/+, the outer contact minus/-.
• The product is not a toy and does not belong in the hands of child-
ren. It should be operated out of the reach of children.
• The use of the surveillance camera does not replace the personal
supervision of children or people who require special assistance,
but serves only as a support to this supervision.
• The camera is suitable for use in indoor and outdoor areas (IP65).
However, it must never be used in or under water, as this will de-
stroy it.
The connector plugs on the camera's connection cable are not wa-
terproof or watertight and must therefore be placed in a dry indoor
area.
• The camera should not be exposed to extreme temperatures, di-
rect sunlight, strong vibrations or heavy mechanical stress.
• Make sure that the connection cable is not pinched, kinked or
damaged by sharp edges.
• Do not leave packaging material carelessly lying around, as it could
become a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts,
blows, or accidental falls, even from a low height.
• If the camera is used with other devices (e.g., a monitor), the oper-
ating instructions and safety notes for these devices must also be
followed without fail.
• Safe operation can no longer be assumed if:
- the device is visibly damaged,
- the device no longer works,
- the device has been stored under adverse conditions for a long
time,
- it was exposed to heavy loads during transport.
• In commercial institutions, the accident prevention regulations of
the Employer's Liability Insurance Association for Electrical Sys-
tems and Operating Facilities are to be observed.
• If you have any questions that are not answered in these operating
instructions, please contact our technical department or another
specialist.
Assembly
The camera should not be pointed directly towards bright sources of
light or the sun, since this will overexpose the image.
For outdoor use we recommend choosing a location that is pro-
tected from rain (e.g., under the eaves) to prevent the formation of
droplets on the camera's front panel that will cause a distorted and
unusable image.
The camera is equipped with a pre-mounted wall bracket. This is to be tight-
ened to a suitable place using three screws. Use appropriate screws and
wall plugs, depending on the surface.
Make sure when screwing into place or when drilling holes that no
cables or wires are damaged.
If the connection cable is to be laid so it is hidden, a correspondingly large
hole has to be drilled underneath the wall bracket, so the plug can be
passed through. The wall bracket will then cover this opening and protect
the cable from intentional damage.
Alternatively, the connection cable can be fed outwards through an open-
ing in the wall bracket. In this case, protect the connection cable with a
suitable cable conduit or similar.
The connection plugs are not waterproof and therefore should be
kept indoors; otherwise they will corrode.
To align the camera, loosen the screws on the bracket using the provided
Allen key.
Place the camera in the desired position and re-tighten the screws.
A precise adjustment can be performed after putting the camera into opera-
tion, when the camera image is displayed on the monitor.