Intended Use; Explanation Of The Symbols; Installation; Safety Instructions - Sygonix 540 TVL Bedienungsanleitung

Operating Instructions
GB
8.5 mm CCD Colour Camera 540 TVL
3.6 mm, 6 mm, 12 mm

Intended Use

This colour camera set is intended for installation in, monitoring and protecting, se-
cluded or critical areas (e.g. entrance areas, surveillance of underground car parks).
The camera features a double front glass structure to prevent refl ections and diffusion
of the IR light from the IR LEDs.
The camera is suitable for use in outdoor areas (IP68).
The voltage is supplied via 12 V/DC (a suitable power transformer is available as an
option).
The inbuilt IR LEDs enable coverage of up to a max. of 20 metres.
The camera's integrated infrared LEDs allow night vision. Please note that coloured
image reproduction changes into black and white monochrome when increasing dark-
ness activates the IR-LEDs. The brightness is detected by the camera using a photo
sensor on the front.
Please bear in mind that it is prohibited by law to observe strangers with a camera
without their knowledge and consent.
Operating the product in any other way than described above is not permitted and may
lead to damage to the product, which can give rise to risks such as short circuit, fi re
and electric shock. The product must not be modifi ed or converted. Always observe the
safety instructions included in these operating instructions. Read the operating instruc-
tions carefully and keep them for later reference.

Explanation of the Symbols

The "lightning" symbol indicates a health hazard, e.g. danger of electric shock.
The exclamation mark indicates particular risks in handling, function and use.
The arrow symbol indicates special tips and operating information.

Safety Instructions

The warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any
consequential damage!
Nor do we assume liability for damage to property or personal injury
caused by improper use or failure to observe the safety instructions. The
warranty will be null and void in such cases.
• The camera must not be modifi ed or converted, as not only will the CE ap-
proval become void but also the warranty.
• The camera should not be exposed to extreme temperatures, direct sun-
light, intense vibrations or heavy mechanical stress.
• Falls from a low height can damage the camera.
• If the device is used with other devices e.g. a monitor, the operating instruc-
tions and safety notices for the connected devices must be followed.
• The use of the surveillance camera system does not replace the personal
supervision of children, or people who require special assistance, but only
serves as a support to this supervision.
• After rapid changes in temperature, the camera requires some time to sta-
bilise, in order to adjust to the ambient temperature, before it can be used.
• Electronic devices are not toys and should be kept out of the reach of chil-
dren!
• Please contact a qualifi ed person, if you are unsure about the safety and
correct use of the system components.
• Never leave the packaging material lying around unattended. Plastic fi lm/
bags, etc. can be dangerous playthings for children; there is a risk of suffoca-
tion.
• If you have reason to assume that safe operation is no longer possible, dis-
connect the device immediately and secure it against inadvertent operation.
The home technology brand for the entire house. More information at www.sygonix.com
• It can be assumed that safe operation is no longer possible, if:
- the device is visibly damaged,
- the device does not function any longer and
- the device has been stored under unfavourable conditions for a long period
of time or
- it has been subjected to considerable stress during transportation.
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operating
Materials are to be observed.
• The camera is suitable for use in outdoor areas (IP68).
• The voltage is supplied via 12 V/DC (a suitable power supply is available as
an option).
• When installing / mounting the appliance, make sure that the connection
cable is neither pinched nor damaged by sharp edges.
• Disconnect the power supply from the power socket if the unit is not to be
used for a while.
• Disconnect the camera from the power supply before cleaning.
• For safety reasons, disconnect the camera from the power supply during
thunderstorms.
• Never pour out fl uids above electrical devices.
• Maintenance, adjustment and repair may only be carried out by a qualifi ed
specialist or a specialised repair shop.
• If you have any questions, which are not answered in this manual, please
contact our technical service or another specialist.

Installation

The connection cables must not be kinked or squeezed. This can result in mal-
functions, short circuits and defects in the device.
Make sure that cables or wires are not damaged when drilling or bolting in
place.
Please note, you should choose a position for your camera that it is not ex-
posed to direct sunlight (this can cause glare). Further, the camera must be
protected from dust and vibration.
The camera's integrated infrared LEDs allow night vision. Please note that
coloured image reproduction changes into black and white monochrome
when increasing darkness activates the IR-LEDs. The brightness is detected
by the camera using a photo sensor on the front.
• Find a suitable location for installing the camera.
Ensure that the plug and socket on the camera's
connection cable are not exposed to damp. Plugs
and sockets may only be used indoors. The cam-
era cable must (for installation in outdoor areas
or in damp rooms) be placed so it is led into a dry
room.
• There are 3 mounting holes in the mounting base.
Hold the mounting base against the desired mount-
ing spot and mark the fi xing holes.
• Drill the holes.
• Fasten the mounting base into place using appro-
priate installation material.
• Screw the mounting base onto the camera and
tighten the knurled locking screws.
• Adjust the camera to the desired position. To do
this, loosen the knurled locking screw and after ad-
justing the camera as required, tighten it again to
secure it in position.
• Attach the sun/rain protection on the camera's casing.