Intended Use; Safety Instructions; Installation - Sygonix 420 TVL Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
CCD Colour Camera Set, 420 TVL,
3.6 mm
Item-No. 75 22 47

Intended use

This camera is meant for mounting in, and protecting, secluded or critical areas (e.g. entrance
areas, surveillance of underground car parks and the like).
The product is designed for use indoors and outdoors (IP65).
The camera is only intended to be used with a stabilised direct current of 12 V/DC (using the
power adapter supplied).
Please bear in mind that it is prohibited by law to observe strangers with a camera without their
knowledge and consent. Observe the rules and regulations of the country where you are using
the camera.
Any use other than that described above may damage the product. Moreover, this may give rise
to hazards such as short-circuiting, fire, electric shock, etc. No part of the product may be mod-
ified or converted!
The safety instructions must be observed at all times!
This product complies with the applicable National and European requirements.
All names of companies and products are the trademarks of the respective owner. All rights
reserved.
Contents
• Colour camera with ceiling/wall holder
• Special cable for video signal and power supply (length approx. 20 m)
• Power adapter
• Allen key
• Operating instructions

Safety instructions

The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
We do not accept liability for damage to property or personal injury caused by
improper handling or non-compliance with the safety instructions! The war-
ranty will be void in such cases.
Dear customer,
these safety instructions are not only to protect the product but also for your own
safety and that of other people. Therefore, please read this chapter very carefully
before using the product for the first time!
a) General
• The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons (CE). Do not open/disassemble! It does
not contain any internal parts that need to be adjusted or maintained by you.
• The product is not a toy and must be kept out of the reach of children. It should be
operated out of the reach of children.
• Make sure that the connection cables are not pinched or damaged by sharp edges.
• If the camera is used with other devices (e.g. a monitor), the operating instructions
and safety notices for these devices must be followed as well.
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• In industrial facilities, the regulations for the prevention of accidents laid down by the
professional trade associations for electrical equipment and facilities must be
adhered to.
• In schools, educational centres, hobby and self-help workshops the operation of
the product is to be supervised by trained employees.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
• If you have any questions that are not answered in this instruction manual, please
contact our technical support centre or consult a professional.
• A safe operation can no longer be assumed, if:
- the device is visibly damaged,
- the device no longer works
- the device was stored for a longer period of time in unfavourable conditions
- heavy loads occurred during transport
www.conrad.com
Version 01/11
°

Installation

The camera is equipped with a pre-mounted wall bracket. This is to be tightened to a suitable
place using three screws. Use appropriate dowels depending on the surface.
If the connection cable should be laid out hidden, a corresponding big opening should be drilled
underneath the wall bracket, to insert the plug. The wall bracket then covers this opening and
protects the cable for mischievous damage.
Alternatively, the cable may be lead outward via a small opening on the side of the wall mount.
Protect the cable with a suitable cable conduit or the like.
Place the camera as desired and fasten it with the delivered Allen keys.
The camera should not be pointed directly at bright sources of light or the sun, since the image
will be overdriven by this.
b) Camera
• The camera is only intended to be used with a stabilised direct current of 12 V/DC.
The inner contact of the round plug should be Plus/"+", the outer contact Minus/"-".
• The camera is suitable for use in indoor and outdoor areas (IP65). However, it
must never be operated in or under water, this will damage it.
• The plugs at the connection cable of the camera are not waterproof or water tight
and must therefore be installed in a dry indoor area.
• The use of the surveillance camera system does not replace the personal super-
vision of children, or people who require special assistance, but only serves as a
support to this supervision.
• The camera should not be exposed to extreme temperatures, direct sunlight,
strong vibrations or heavy mechanical stress.
• Make sure that the connection cable is not pinched or damaged by sharp edges.
• Disconnect the power supply from the power socket if the camera will not be used
for a while (e.g. storage).
b) Power adapter
• The design of the power adapter complies with protection class II. Only use a stan-
dard mains socket as the voltage source (see section „Technical data").
• The power adapter is only intended for use in dry indoor rooms; it must not get
damp or wet; never touch it with wet hands!
There is a risk of life-threatening electric shock!
Protect the power adapter from direct solar radiation, strong heat (>35°C), cold
(<0°C), dust and dirt, vibrations or mechanical loads.
• When the product is taken from a cold to a warm room (e.g. during transport), con-
densation may be produced.
Allow the product to reach room temperature before you connect it to the mains
voltage. This may take several hours. Otherwise, there is lethal danger due to an
electric shock!
• Do not pull the power adapter from the mains socket by pulling on the cable.
• If the power adapter is damaged, do not touch it; there is danger to life from elec-
tric shock!
Switch off the mains voltage to the mains socket to which the power adapter is con-
nected (switch off at the corresponding circuit breaker or remove the safety fuse).
You can then unplug the power adapter from the mains socket. Dispose of the
damaged power adapter in an environmental-friendly way, do not use it any more.
Replace it with a new wall plug transformer with the same specifications.
For outdoor use we recommend to choose a location that is protected from rain (e.g.
under the eaves) to prevent the formation of droplets on the camera's front panel that
will cause a distorted and unusable image.
Make sure when screwing into place or when drilling holes that cables or wires are
not damaged.
The connection plugs are not waterproof and should be kept indoors, otherwise they
will corrode.