Interrupting Operation - Kärcher HDS 6/10-4 C Classic Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für HDS 6/10-4 C Classic:

Inhaltsverzeichnis

Verfügbare Sprachen

–

Always unwind extension lines completely.

–

The plug and coupling of the extension cable used

must be watertight.

DANGER

Danger of explosion! Do not spray flammable liquids.

DANGER

Risk of injury! Never use the appliance without the spray

lance attached. Check and ensure proper fitting of the

spray lance prior to each use. The screw connection of

the spray lance must be finger-tight.

DANGER

Risk of injury! Hold the hand spray gun and the spray

pipe firmly with both hands.

DANGER

Risk of injury! The trigger and safety lever may not be

locked during the operation.

DANGER

Risk of injury! Contact Customer Service if the safety le-

ver is damaged.

ATTENTION

Risk of damage! Never operate device with an empty

fuel tank. The fuel pump will otherwise be destroyed.

Opening/closing the trigger gun

 To open the trigger gun: Actuate the safety lever

and trigger.

 To close the hand spray gun: Release the safety le-

ver and trigger.

Replace the nozzle

DANGER

Risk of injury! Switch the appliance off prior to replacing

nozzle and activate hand spray gun until device is pres-

sureless.

 Secure the trigger gun. To do so, push the safety

catch towards the front.

 Replacing the nozzle.

Turning on the Appliance

 Set appliance switch to desired operating mode.

Indicator lamp for operational readiness lights up.

The device starts briefly and turns off, as soon as the

working pressure is reached.

Note: If the control lamp "rotation direction" lights up,

please switch the appliance off immediately and fix the

error, see "Help with malfunctions".

 Release the trigger gun. To do so, push the safety

catch towards the back.

When activating the hand spray gun the device switch-

es back on.

Note: If no water comes out of the high pressure nozzle,

vent pump. Refer to "Help with malfunctions - appliance

is not building up pressure".

Adjust cleaning temperature

 Set device switch to desired temperature.

Set working pressure and flow rate

Pressure/quantity regulation of the pump unit

 Turn the regulation spindle in a clockwise direction:

Increase working pressure (MAX).

 Turn the regulation spindle in an anti-clockwise di-

rection: Reduce working pressure (MIN).

Operation

Operation with detergent

–

For considerate treatment of the environment use

detergent economically.

–

The detergent must be suitable for the surface to

be cleaned.

 With support of the detergent dose valve set deter-

gent concentration as determined by the manufac-

turer.

Note: Recommended values at the control panel at

maximum working pressure.

Note: If detergent is be suctioned from an external con-

tainer, route the detergent suction hose through the re-

cess to the outside.

 Set pressure/temperature and detergent concen-

tration according to the surface to be cleaned.

Note: To prevent damage due to too much pressure, al-

ways position high pressure ray first from a greater dis-

tance towards object to be cleaned.

Recommended cleaning method

–

Loosen the dirt:

 Spray detergent economically and let it work for

1...5 minutes but do not let it dry up.

–

Remove the dirt:

 Spray off loosened dirt with the high pressure jet.

Operating with cold water

Removal of light contaminations and clear rinse, i.e.:

Gardening tools, terrace, tools, etc.

 Set operating pressure according to need.

The appliance works in the most economical tempera-

ture range (max. 60 °C).

Operating with hot water

DANGER

Scalding danger!

 Set device switch to desired temperature.

We recommend the following cleaning temperatures:

–

Light contaminations

30-50 °C

–

Contaminations containing protein, i.e. in the food

processing industry

max. 60 °C

–

Vehicle cleaning, machine cleaning

60-90 °C