Before Starting The Machine; Operation - EINHELL BT-BJ 900 Bedienungsanleitung

Anleitung BT-BJ 900_SPK1:_
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

6. Before starting the machine

Before you connect the machine to the mains sup
ply make sure that the data on the model plate
are identical to the mains data.
The adapter for the dust extraction system (5) and
the dust bag (2) must be fitted (Fig. 2).

7. Operation

7.1 Setting the cutting depth (Fig. 3)
Set the required cutting depth with the setting
wheel (3).
The designations on the setting wheel reflect the
various sizes of biscuit dowels
Push the drive motor (11) forwards to check the
cutting depth. The plug must be disconnected
from the mains supply for this purpose.
You can adjust the cutting depth setting using the
screw (a).
7.2 Setting the cutting angle and cutting height
(Fig. 4)
Undo the two locking levers (2).
Important! The set angle is indicated by the arrow
(b). The set height is indicated by the edge
belonging to the angle arrow (b) in question.
Set the angle stop (10) to the required angle. You
can select between angles of 45°, 90° and 135°.
Set the required height on the height scale (a); the
height of the groove should always be in the
center of the workpiece.
Now retighten the two locking levers (2).
A single pass will suffice for thin workpieces.
Several passes over the workpiece are required
for thicker workpieces.
7.3 Changing the cutter (Figs. 5-8)
Important! The plug must be disconnected from
the mains supply.
Remove the cover (a).
Place the face spanner (7) on the flange (b).
Press the locking knob; hold this knob and turn
22.08.2007 8:59 Uhr Seite 11
the face spanner in the direction in which the
machine turns. After approximately half a turn the
locking knob will engage and the flange can be
released.
Release the cutter (c) from the flange (d). You can
use the face spanner (7) as an aid.
Then pull the cutter (c) out of the base plate (9).
Again, you can use the face spanner (7) as an
aid.
Now fit the new cutter following the above
instructions in reverse. Check that the direction of
rotation of the cutter is correct.
Refasten the cover (a).
Never press the locking knob (8) when the motor
is running. Ensure that the cutter is perfectly
secure before you start work.
8. Working with the biscuit jointer
8.1 ON/OFF switch (1)
To switch on the equipment slide the switch(1)
forwards and press the switch (1) until it engages.
To switch off the machine push the switch (1); it
then returns to its original position.
8.2 Making a workpiece (Fig. 9)
Before you start work with the biscuit jointer, the
workpiece must be marked as follows.
Place the two parts side by side; the workpieces
must be securely clamped.
Draw a line with a pencil perpendicular to the
position of the joint.
Several joints will be required for large pieces of
wood.
The distance between two lines should be at least
10 cm.
8.3 Positionin the biscuit jointer (Fig. 10/11)
Set and check the cutting depth.
Set the angle fence (10).
Set the height.
Position the machine near to the workpiece.
There are markings (a) on the machine; these
must line up with the line you have drawn.
Now switch on the machine and push the drive
motor (11) forwards. The workpiece must be se-
curely clamped.
GB
11