Before Starting The Equipment - EINHELL TC-PN 50 Originalbetriebsanleitung

5. Before starting the equipment

Before you connect the equipment to the power
supply make sure that the data on the rating plate
are identical to those of the supply voltage.
Disconnect the compressed air supply before
performing any cleaning, adjusting and main-
tenance work.
Air supply:
Via a compressed air source with pressure setting
function, e.g. a compressor. Before starting up,
please also read the section on care and mainte-
nance.
Setting values for work:
Set a maximum working pressure of 8.3 bar at
your compressed air supply.
Remember:
Wear the necessary protective clothing when
working with the stapler, in particular safety
goggles.
Pay attention to the safety regulations.
•
Before starting work each time, check that the
magazine is securely fastened (Fig. 1/Item E).
Clean the equipment thoroughly and immedi-
ately each time after it has been used.
•
Each time before starting work, check that the
trigger catch functions perfectly and that all
screws and nuts are securely fastened.
•
Never tamper with the stapler.
•
Never dismantle or block any parts of the
stapler such as, e.g. a trigger catch.
•
Never carry out any "emergency repairs" with
unsuitable means.
•
Proper stapler maintenance is required at
regular intervals in accordance with the infor-
mation supplied by the manufacturer.
•
Take precautions to prevent anything which
would weaken or damage the equipment, e.g.
from
a) striking or engraving,
b) modifi cations which are prohibited by the ma-
nufacturer,
c) guiding on templates made of hard material,
e.g. steel,
d) pushing across the fl oor,
e) using as a hammer,
f) any kinds of acts of violence.
Anl_TC_PN_50_SPK9.indb 17
https://tm.by
Интернет-магазин TM.by
GB
5.1 Checking the trigger catch
Check the trigger catch (Fig. 1/Item H) each time
before using. The trigger catch must move freely
without catching. The spring on the trigger catch
must return the trigger catch to the released initial
position. Never use the equipment if the trigger
catch is not working.
1. Disconnect the equipment from the air supply.
2. Remove the staples/nails from the magazine
(Fig. 1/Item E).
3. Check that the trigger and the trigger catch
can move up and down freely.
4. Connect the equipment to the air supply.
5. Press the trigger catch against the workpiece
without pressing the trigger. The equipment
should not operate. Never use the equip-
ment if it operates without the trigger being
pressed. Risk of injury!
6. Remove the equipment from the workpiece.
The trigger catch must return to the released
initial position. Press the trigger. The equip-
ment should not operate. Never use the
equipment if it operates. Risk of injury!
7. Press the trigger and press the trigger catch
against the workpiece. The equipment opera-
tes.
8. Press the trigger catch against the workpiece
and press the trigger; the equipment opera-
tes.
5.2 Loading staples and nails
•
When you fill the magazine (Fig. 1/Item E),
make sure that you hold the equipment in
such a way that the muzzle is pointed neither
at you or anyone else.
•
To fill the magazine, press the magazine lever
(Fig. 1/Item C) and slide back the magazine
cover (Fig. 1/Item D) as far as it will go.
•
Insert the staples as shown in (Fig. 3) or the
nails as shown in (Fig. 4).
•
Do not insert more than one complete stick
of staples/nails, otherwise the magazine will
be overfilled and you will not be able to close
it again. Slide the magazine cover forward
again until it snaps into place.
•
The level indicator (Fig. 5/Item F) shows the
number of loaded staples / nails if less than
50 are loaded.
- 17 -
06.03.2019 10:14:21