Home Motion Detect Setup - JVC TK-C676 Bedienungsanleitung

HOME MOTION DETECT Setup

Use the HOME MOTION DETECT screen to set the areas to be excluded from the target area of the motion detect function. (which
outputs an alarm upon detection motion in the monitored picture)
MENU button
SET button
REMOTE CONTROL UNIT
CAMERA POSITION
SETUP
POWER
ALARM
MENU SET AUTO F-1
KEY LOCK
LENS CAMERA/POSITION
1 2 3
CAMERA POSI-
SPEED
TION
4 5 6
IRIS OPTION OPTION
CLOSE OPEN
1 2
FOCUS
7 8 9 AUTO AUTO
NEAR FAR
AF
PAN PATROL
0
ZOOM TELE CLEAR ENTER
WIDE
/HOME
ENTER
button
– – – M E N U – – –
C A M . F U N C T I O N . .
C A M . T I T L E / A L A R M . .
C A M . V I D E O A D J U S T . .
C A M . A L C / E x D R . .
H O M E M O T I O N D E T E C T . .
A U T O P A N / P A T R O L / T R A C E . .
P O S I . F U N C T I O N S E T . .
F A C T O R Y S E T T I N G S . .
SETUP menu display on the camera
– – – H O M E M O T I O N D E T E C T – – –
M O D E O F F
L E V E L – – –
A R E A E D I T . .
A L A R M D I S P L A Y 5 s
D E M O N S T R A T I O N . .
HOME MOTION DETECT menu
Blinking
AREA EDIT screen
– – – D E M O N S T R A T I O N – – –
DEMONSTRATION screen
RM-P2580
F-2 F-3
Numeric keys
CAMERA
PAN/TILT
buttons
PAN/TILT
lever
1.
Select the camera. (
CAMERA button → Numeric key (camera number) → ENTER button.
The picture of the selected camera is output.
2.
Display the SETUP menu on the camera.
1 4
( P. 18, steps to
MENU button (3 sec.) → Select "CAMERA" with the PAN/TILT lever
→ SET button.
The camera moves to the home position.
3.
Tilt the PAN/TILT lever up or down to move the cur-
sor (>) to "HOME POSITION DETECT" and press
the SET button.
The HOME POSITION DETECT menu is displayed.
4.
Move the cursor (>) to "AREA EDIT" and press the
SET button.
The AREA EDIT setting screen is displayed. (The frame display
position is moved slightly upward from the center of the screen.)
5.
Tilt the PAN/TILT lever to select the area to be ex-
cluded from the motion detection target area.
The area blinking in white is moved by the operation of the lever.
6.
Press the SET button.
• The area to be excluded is set and blinks in gray.
• To cancel, press the SET button again.
• When the setting is canceled, the gray blinking changes to white
blinking.
7.
5
Repeat steps and
from the motion detection target area.
Complete the setup of all excluded areas in this way.
8.
Press the MENU button.
The screen returns to the precious menu.
MEMO
The positions of areas in the picture are reference positions. Check the actu-
al positions in the actual picture.
The areas set to be excluded from the motion detection target area can be
confirmed in the DEMONSTRATION screen.
The motion detect function is not intended to prevent fire or theft. There-
fore, JVC will not assume any liabilities for accidents and damage relat-
ed to the use of this function.
RM-P2580 Instruction manual)
)
6
for each area to be excluded
E-33