Siemens Simatic C7-621 Handbuch Seite 139

ORGANIZATION_BLOCK "OB82"
TITLE =
VERSION : 0.0
VAR_TEMP
OB82_EV_CLASS : BYTE
OB82_FLT_ID : Byte;
OB82_PRIORITY : BYTE ;
OB82_OB_NUMBR : BYTE ;
OB82_RESERVED_1 : BYTE ;
OB82_IO_FLAG : BYTE ;
OB82_MDL_ADDR : INT ;
OB82_MDL_DEFECT : BOOL ;
OB82_INT_FAULT : BOOL ;
OB82_EXT_FAULT : BOOL ;
OB82_PNT_INFO : BOOL ;
OB82_EXT_VOLTAGE : BOOL ;
OB82_FLD_CONNCTR : BOOL ;
OB82_NO_CONFIG : BOOL ;
OB82_CONFIG_ERR : BOOL ;
OB82_MDL_TYPE : BYTE ;
OB82_SUB_NDL_ERR : BOOL ;
OB82_COMM_FAULT : BOOL ;
OB82_MDL_STOP : BOOL ;
OB82_WTCH_DOG_FLT : BOOL ;
OB82_INT_PS_FLT : BOOL ;
OB82_PRIM_BATT_FLT : BOOL ;
OB82_BCKUP_BATT_FLT : BOOL ;
OB82_RESERVED_2 : BOOL ;
OB82_RACK_FLT : BOOL ;
OB82_PROC_FLT : BOOL ;
OB82_EPROM_FLT : BOOL ;
OB82_RAM_FLT : BOOL ;
OB82_ADU_FLT : BOOL ;
OB82_FUSE_FLT : BOOL ;
OB82_HW_INTR_FLT : BOOL ;
OB82_RESERVED_3 : BOOL ;
OB82_DATE_TIME : DATE_AND_TIME ; //Date and time OB82 started
t_req : BOOL ;
t_busy : BOOL ;
t_return : INT ;
t_laddr : WORD ;
END_VAR
BEGIN
NETWORK
TITLE =
L #OB82_MDL_ADDR;
T #t_laddr;
SET ;
= #t_request;
loop: NOP 0;
CALL SFC 59 (
Komplettgeräte C7-621, C7-621 ASi
C79000-G7000-C622-01
//16#39, Event class 3,Entering event state
//16#xx Fault identification code
//26/28 (Priority of 1 is lowest)
//82 (Organization block 82, OB82)
//Reserved for system
//Input (01010100), Output (01010101)
//Base address of module with fault
//Module defective
//Internal fault
//External fault
//Point information
//External voltage low
//Field wiring connector missing
//Module has no configuration data
//Module has configuration error
//Type of module
//Sub-Module is missing or has error
//Communication fault
//Module is stopped
//Watch dog timer stopped module
//Internal power supply fault
//Primary battery is in fault
//Backup battery is in fault
//Reserved for system
//Rack fault, only for bus interface module
//Processor fault
//EPROM fault
//RAM fault
//ADU fault
//Fuse fault
//Hardware interupt input in fault
//Reserved for system
//Anstoß für RD_REC
//Busy von RD_REC
//ReturnValue von RD_REC
//Baugruppenadresse
//Adresse der alarm-
//gebenden Baugruppe
//zwischenspeichern
//Anstoßbit für RD_REC = 1
ASi Einsatz und Funktion
6-35