Specifications; Important Safety Instructions - Makita 4190D Betriebsanleitung

ENGLISH
(Original instructions)
1 Set plate
2 Battery cartridge
3 Depth guide
4 Bolt (A)
5 Hex wrench
6 Bevel scale plate
7 Bolt (B)
8 Blade case

SPECIFICATIONS

Model
Wheel diameter .................................................... 80 mm
Cutting depth
90° ............................................................... 0 – 18 mm
45° ............................................................... 0 – 16 mm
-1
No load speed (min ) ........................................... 1,000
Overall length ..................................................... 313 mm
Net weight ............................................................. 1.9 kg
Rated voltage .................................................. D.C. 9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for cutting in glass and masonry
materials with a diamond wheel and water.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
4
Explanation of general view
9 Base
10 Lock-off lever
11 Switch trigger
12 Bolt
13 Flange
14 Diamond wheel
15 Hex wrench
16 Blade stopper pin
4190D
7.
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
GEA010-1
2.
3.
4.
CORDLESS CUTTER SAFETY WARNINGS
1.
ENC004-1
2.
3.
4.
17 Tank holder installing portion
18 Tank
19 Screw (B)
20 Screw (A)
21 Tank holder
22 Cap
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Read all safety warnings, instructions, illustra-
tions and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or seri-
ous injury.
Always use guard provided with the tool. The
guard must be securely attached to the power
tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the
operator. The guard helps to protect operator from
broken wheel fragments and accidental contact with
wheel.
Use only diamond cut-off wheel for your power
tool. Just because the accessory can be attached to
your power tool, it does not assure safe operation.
The rated speed of the wheel must be at least
equal to the maximum speed marked on the
power tool. Wheels running faster than their rated
speed can break and fly apart.
GEB053-2