Inhaltsverzeichnis
Werbung
GB
SØJLEBOREMASKINE MED LASER
D
Lœs denne brugsanvisning godt igennem før maskinen tages i brug. Sørg for at De
kender maskinens funktion og betjening. Vedligehold maskinen i følge
instruktionerne, for at maskinen altid kan fungere optimalt. Bevar denne
NL
brugsanvisning og den vedlagte dokumentation til maskinen.
Beskrivelse
F
Deres søjleboremaskine er blevet designet til at bore huller i træ, metal og plastik.
Indhold
E
1.
Information om maskinen
2.
Sikkerhedsforskrifter
P
3.
Montage
4.
Brug
5.
Vedligeholdelse
I
1. INFORMATION OM MASKINEN
S
Tekniske specifikationer
FIN
Spœnding
Frekvens
Optaget effekt
N
Omdrejninger, ubelastet
Omdrejninger
Borehovedets kap.
DK
Spindelkegle
Bordpladens mål
Bordpladens mål (med udvidelsesstykkerne)
Højde
Vœgt
Lpa (lydtryk)
Lwa (lydeffektniveau)
Beskrivelse
Fig. A
1.
Tænd/sluk-kontakt
2.
Motorkasse
3.
Stativ
4.
Opbevaringsrum
5.
Bord
6.
Borepatron
7.
Sikkerhedsafskærmning
8.
Boreløftestang
96
230 V~
50 Hz
500 W
425 - 2545/min
12
16 mm
MT2
200 x 200 mm
200 x 240 mm (max. 330 mm)
850 mm
39.5kg
64.9 dB(A)
77.9 dB(A)
Ferm
Adjusting the table
Fig. E
The table can be height-adjusted, turned and toppled.
Height adjustment:
•
Slacken the locking handle (34).
•
Turn the handle (19) to adjust the table (5) to the required height.
•
Tighten the locking handle.
Turning:
•
Slacken the locking handle (34).
•
Turn the table (5) to the required position.
•
Tighten the locking handle.
Toppling:
•
Slacken the locking screw (35).
•
Topple the table (5) to the required position.
•
Tighten the locking screw.
Adjusting the table extenders
Fig. F
Using the table extenders you can support long workpieces.
•
Slacken the wing nuts (36).
•
Slide the extender (37) outward.
•
Tighten the wing nut.
Adjusting the speed
Fig. G
•
Remove the screw (38) and open the cover (39).
•
Slacken the screw (40) and push the motor housing (2) to the front to release the tension on
the rear V-belt (41).
•
Put the V-belts in line on the pulleys (42) in one of the combinations specified on the inside
of the cover. In order to adjust the front V-belt (43) it is necessary to temporarily remove the
rear V-belt (41).
•
Push the motor housing to the rear to tension the V-belt.
•
Clamp the motor housing in position by tighening the screw (40).
•
Close the cover and re-fit the screw (38).
Switch off the machine and wait until the machine has come to a complete standstill
before changing the speed.
Adjust the speed to the material to be drilled and the drilling diameter:
•
For drilling in wood, choose a high speed.
•
For drilling in metal and plastics, choose a lower speed as the drilling diameter increases.
Instructions for use
•
Use waste material to practise your skills and to learn operating the machine first.
Ferm
GB
D
NL
F
E
P
I
S
FIN
N
DK
13
Werbung
Inhaltsverzeichnis
