Specifications - Hitachi DV 14DVF Bedienungsanleitung

c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.

SPECIFICATIONS

POWER TOOL
Model
No-load speed (Low/High)
No-load impact rate (Low/High)
Brick
(Depth 30 mm)
Wood
Drilling
(Thickness 18 mm)
Metal
Capacity
(Thickness 1.6 mm)
Machine screw
Driving
Wood screw
Rechargeable battery
Weight
CHARGER
Model
Charging voltage
Weight
0 – 400 / 0 – 1500 min
0 – 5600 / 0 – 21000 min
8 mm (diameter) × 50 mm (length)
(Requires a pilot hole)
EB1414S: Ni-Cd 14.4 V (1.4 Ah 12 cells)
BCC1412: Ni-Cd 14.4 V (1.2 Ah 12 cells)
UC18YK / UC18YG
7.2 – 18 V
0.3 kg
PRECAUTIONS FOR CORDLESS IMPACT
DRIVER DRILL
1. Always charge the battery at a temperature of 0°C – 50°C.
A temperature of less than 0°C will result in over charging
which is dangerous. The battery cannot be charged at a
temperature higher than 50°C.
The most suitable temperature for charging is that of
20°C – 25°C.
2. When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
Do not charge more than two batteries consecutively.
3. Do not allow foreign matter to enter the hole for connecting
the rechargeable battery.
4. Never disassemble the rechargeable battery and
charger.
5. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric current
and overheat. It results in burn or damage to the battery.
6. Do not dispose of the battery in fi re.
If the battery is burnt, it may explode.
7. When drilling in wall, fl oor or ceiling, check for buried
electric power cord, etc.
8. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
9. Using an exhausted battery will damage the charger.
10. Do not insert object into the air ventilation slots of the
charger.
Inserting metal objects or infl ammables into the charger
air ventilation slots will result in electrical shock hazard or
damaged charger.
11. Do not move the charger by pulling it by the cord. Doing
so may lead to damage.
12. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
DV14DVF
-1
-1
13 mm
32 mm
13 mm
6 mm
1.8 kg
English
DV18DVF
0 – 400 / 0 – 1500 min
0 – 5600 / 0 – 21000 min
13 mm
38 mm
13 mm
6 mm
8 mm (diameter) × 75 mm (length)
(Requires a pilot hole)
EB1814SL: Ni-Cd 18 V (1.4 Ah 15 cells)
BCC1812: Ni-Cd 18 V (1.2 Ah 15 cells)
1.9 kg
-1
-1
9