...mit dem Kauf dieses Garagentorantriebs haben CE-Zeichen und Konformität Sie sich für ein Qualitätsprodukt aus dem Hause Das vorliegende Produkt erfüllt die Anforderun- RADEMACHER entschieden. Wir danken Ihnen für gen der geltenden europäischen und nationalen Ihr Vertrauen. Richtlinien. Der RADEMACHER Garagentorantrieb ist unter Die Konformität wurde nachgewiesen, die entspre-...
Entfernen der Torverriegelungen ......11 Monatliche Prüfung der Hinderniserkennung Maß nehmen ............12 (Kraftbegrenzung) ..........33 Zusammenbau der Schienen Technische Spezi kationen ........34 (nur für RP-SX5-900N-3) .........13 Technische Daten ............34 Den Zahnriemen spannen ........13 Fehlerbehebung ............35 Verbindung des Antriebsgehäuses mit der Schiene ............14 EG-Konformitätserklärung ........36...
6 x Dübel (10 mm) 6 x Sechskantschraube (8 x 60 mm) 1 x Schlagdorn 2 x Montagelochband – RP-SX5-900N-3 dreiteilige Schiene + zwei Verbinder – RP-SX5-900N-1 einteilige Schiene ohne Verbinder 1 x Codierschaltgerät mit Funk RP-SX5-CSG-AF26 (nur bei RP-SX5-900N-3 enthalten)
Richtige Verwendung Verwenden Sie den Garagentorantrieb aus- Richtige Verwendung des Handsenders schließlich: Die Fernsteuerung per Handsender ist nur für Geräte zum Ö nen und Schließen von Garagentoren und Anlagen zulässig, bei denen eine Funkstörung im Sender oder Empfänger keine Gefahr für Menschen, im privaten Bereich Tiere oder Gegenstände ergibt oder das Risiko durch gemäß...
Zulässige Garagentorarten ausschwingende Standard-Schwingtore Sektionaltore Die Tore müssen leichtgängig sein und den Anforde- rungen folgender Normen entsprechen: EN 12453 und EN 12604. Schwingtore Deckensektionaltore Unzulässige Garagentorarten Tore, die Kipp- und Drehbewegungen erfordern, Nicht ausschwingendes dürfen nicht mit dem Garagentorantrieb SX5 Kipptor betrieben werden.
Allgemeine Sicherheitshinweise Durch unsachgemäßen Gebrauch besteht er- Wichtige Sicherheitsanweisungen höhte Verletzungsgefahr. ACHTUNG Für die Sicherheit von Personen ist es Lebens- Greifen Sie nie in das fahrende Tor oder in bewegte wichtig, alle Anweisungen zu befolgen. Teile. Diese Anweisungen aufbewahren. Unterweisen Sie alle Personen, die das Garagentor bedienen, im sicheren Gebrauch.
Funktionsbeschreibung Intelligenter Mikrocomputer Automatische Schließfunktion Intelligente, computergesteuerte, exakte Hubposi- Die automatische Schließzeit des Tores kann von 30 bis tionierung, zeitnahe Kraftermittlung, Rücklauf beim 240 Sekunden eingestellt werden (siehe Seite 24/25). Auftre en auf Hindernisse. 2000-Zyklen-Alarm Antrieb Wenn der Antrieb 2000 Zyklen durchlaufen hat, ertönt Geringer Lärm, Softstart und Softstop schützen den ein Signalton, um den Anwender daran zu erinnern, Antrieb und gewährleisten eine lange Lebensdauer.
Funktionsbeschreibung / Notentriegelung Das Tor kann im Falle eines Stromausfalls durch Zie- hen am Seil der Notentriegelung von Hand bedient werden. Es besteht Verletzungsgefahr. Das Tor kann beim Entriegeln unkontrolliert herunterfallen (z. B. wenn Federn schwach oder gebrochen sind oder wenn das Tor nicht im Gleichgewicht ist). Schließen oder ö...
Notwendige Werkzeuge Sie benötigen folgende Werkzeuge Entfernen der Torverriegelungen Demontieren Sie alle senkrechten und waa- gerechten Torverriegelungen. WICHTIG! Heben Sie die „alten“ Torverriegelungen gut auf. Falls Sie den Garagentorantrieb einmal demon- tieren, müssen Sie diese wieder montieren um den Originalzustand des Tores wieder herzu- stellen.
Maß nehmen Tormitte ausmessen und markieren Markieren Sie die Tormitte wie gezeigt an der Torober- kante, am Torsturz und an der Garagendecke. Abstand zwischen Toroberkante und Decke Schwingtor ermitteln min. 6 cm Schließen Sie das Tor langsam und messen Sie den Abstand zwischen Toroberkante und Decke.
Zusammenbau der Schienen (nur für RP-SX5-900N-3) HINWEIS Der RolloPort SX5 wird mit drei Schienen geliefert: zwei Endstücke, inkl. vormontiertem Zahnriemen ein Mittelteil (ohne Zahnriemen) mit zwei Verbin- dern. Legen Sie die beiden Endstücke mit dem vormon- tierten Zahnriemen so auf den Boden, dass der Zahnriemen möglichst gerade zwischen Ihnen...
Verbindung des Antriebsgehäuses mit der Schiene Setzen Sie zuerst den Vielzahnverbinder (5) ein. WICHTIG Achten Sie darauf, dass der Mikroschalter (3) bei der Setzen Sie die Schiene (4) mit dem innenliegen- Montage der Schiene nicht beschädigt wird. den Ritzel (ab Werk in der Schiene vormontiert) über den Verbinder (5).
Seite 15
Verbindung des Antriebsgehäuses mit der Schiene Alternative Montage des Antriebs quer zur Schiene. WICHTIG Beim allen Arbeiten am Mikroschalter (3) be- Der Mikroschalter (3) muss immer am Ende der Schiene steht Lebensgefahr durch Stromschlag. positioniert sein. Daher muss der Mikroschalter (3) Lassen Sie den Mikroschalter (3) nur durch eine bei der Quermontage des Antriebs entsprechend zugelassene Elektrofachkraft umsetzen.
Befestigung des Antriebs und der Schiene A / B / C / D, siehe folgende Seiten Sturzmontage Die Montage sollte vorzugsweise am Sturz erfolgen, Sturz- da so die auftretenden Kräfte optimal aufgenommen montage min. 1,5 cm werden können. Deckenmontage Für die Deckenmontage sollten Sie den Sturzwinkel um 90 Grad drehen und weiter innen an der Garagendecke befestigen.
(A) Montage des Sturzwinkels (1) HINWEIS Der Sturzwinkel (1) muss mittig zum Tor montiert werden. Zeichnen Sie die Position des Sturzwinkels (1) Legende an und bohren Sie die Montagelöcher (z.B. mit 1 = Sturzwinkel einem 10 mm Steinbohrer). 2 = Schraube (6 x 80 mm) mit Schrauben Sie den Sturzwinkel (1) mit den bei- Sechskantmutter liegenden Sechskantschrauben (8 x 60 mm) fest.
(C) Montage des Torwinkels (8) HINWEIS Wir empfehlen Ihnen den Torwinkel (8) vorzugsweise am Torrahmen zu befestigen. Für Kunststo - oder dünnwandige Holztore sind zu- sätzliche Verstrebungen nötig, um eine Beschädigung des Tores zu vermeiden. Sprechen Sie in diesem Fall mit Ihrem Torlieferanten.
(C) Montage des Torwinkels (8) Schrauben Sie den Torwinkel (8) mit den beilie- genden Sechskant-Blechschrauben (8 x 15 mm) am Rahmen fest. Befestigen Sie zum Schluss den Toranbinder (12) mit dem beiliegenden Bolzen (9) am Tor- winkel (8). HINWEIS Ab Werk ist schon ein gerader Toranbinder vormon- tiert, dieser ist fest mit der Schiene verbunden.
Wichtige Hinweise nach der Montage Stellen Sie sicher, das die Anlage nach der Mon- Stellen Sie sicher, dass der Antrieb nach der tage ordnungsgemäß eingestellt ist, und dass Montage die Ö nungsbewegung des Tores ver- der Antrieb reversiert (zurückfährt), falls das Tor hindert oder stoppt, wenn das Tor mit einer einen 50 mm hohen, auf dem Boden be ndlichen Masse von 20 kg beladen ist, die zentral an...
Endpunkte einstellen / Oberen Endpunkt einstellen Die falsche Reihenfolge bei der Einstellung der Korrekte Einstellreihenfolge: Endpunkte führt zu Fehlfunktionen. Halten Sie 1. oberen Endpunkt einstellen unbedingt die vorgegebene Einstellreihenfolge 2. unteren Endpunkt einstellen ein. 1. Drücken Sie „P“ für 2. Der Antrieb erzeugt 3.
Referenzfahrt zur Kraftmessung durchführen Während der Referenzfahrt besteht Verlet- zungsgefahr, da der Antrieb sehr große Kräfte entwickelt. 1. Drücken Sie „+“, in der 2. Drücken Sie „P“, 3. Das Tor hebt sich auto- Anzeige erscheint „3“. „3“ blinkt. matisch. 4. Drücken Sie nach dem 5.
Kraftbegrenzung bei Bedarf anpassen HINWEIS Ein zu niedriges Kraftniveau beeinträchtigt Der Antrieb ist ab Werk auf Stufe 3 eingestellt. Bei die Torbewegung, besonders wenn die mecha- Bedarf (z.B. bei zu niedrigem Kraftniveau) können Sie nische Struktur des Tores nicht gut ausbalan- die Kraftbegrenzung nachträglich anpassen.
Alarmeinstellung Wenn der Alarm eingeschaltet ist erzeugt der Beenden des Alarmtons: Antrieb einen Signalton, wenn das Tor länger Drücken Sie die Torsteuerungstaste, um das Tor voll- als 10 Minuten geö net ist. Der Signalton ständig zu schließen. ertönt alle 10 Minuten für 30 Sekunden. 1.
Automatische Schließzeiteinstellung 4. Drücken Sie „+“ und 5. Drücken Sie „P“ um die 6. Programmierung ab- wählen Sie die gewün- Einstellung zu spei- schließen, (s. Seite 28, schte Schließzeit: chern. Methode 2) oder weiter mit nächster Einstel- 1 = 30 s 5 = 150 s lung.
Einstellen der Au ahrgeschwindigkeit Mit Hilfe dieser Funktion können Sie die Geschwindig- Die Einstellung der Au ahrgeschwindigkeit erfolgt in keit der Aufbewegung je nach individuellem Bedarf cm/s (Zentimetern pro Sekunde). einstellen. 1. Drücken Sie auf „+“ 2. Drücken Sie „P“, die 3.
Einschalten der Back-Jump Funktion Funktion Nach dem Schließen entlastet die Back-Jump Funktion den Antriebsstrang durch ein kurzes (10 mm) Fahren in Gegenrichtung. 1. Drücken Sie auf „+“ 2. Drücken Sie „P“, die 3. Drücken Sie „+“, die Anzeige ist „0“. Anzeige ist „1“.
Programmierung abschließen WICHTIG HINWEIS Bitte beachten, dieser abschließende Schritt muss aus- Sie können die Programmierung wie folgt auf 2 Arten geführt werden, da die gespeicherten Informationen abschließen: ansonsten verloren gehen. Methode 1: Diese Methode unbedingt nach der Referenzfahrt durchführen 1. Drücken Sie nach der 2.
Handsender an- und abmelden Handsender anmelden: 1. Drücken Sie „S“ für ca. 2. Die Zehneranzeige im 3. Drücken Sie 2 x auf eine 3 Sekunden und lassen Display ist „0“. beliebige Taste des Sie los. Handsenders. Die „0“ erlischt und der Handsender ist ange- meldet.
Anschluss elektrischer Zusatzeinrichtungen Die unsachgemäße Montage von externen Bei allen Arbeiten an elektrischen Anlagen be- Tastern kann die Betriebssicherheit gefähr- steht Lebensgefahr durch Stromschlag. den. Der Anschluss von elektrischen Zusatzeinrichtun- gen darf nur durch eine zugelassene Elektrofach- Montieren Sie Innentaster, Codierschalter etc. immer: kraft erfolgen.
Manueller Betrieb des Tores Im Falle eines Stromausfalls: Wollen Sie das Tor bei Stromausfall manuell Es besteht Verletzungsgefahr. Das Tor kann bedienen, müssen Sie am Seil der Notentriege- beim Entriegeln unkontrolliert herunterfallen lung ziehen, damit diese das Tor vom Antrieb (z.B.
Anleitung für den Anwender Wenn der Strom wieder zur Verfügung steht, Hinweise für den Einsatz können Sie den Handsender oder die Wand- Überprüfen Sie das Antriebssystem um festzustel- konsole bedienen, die Notentriegelung rastet len, ob es sich beim ersten Einsatz des Garagentor- auto matisch ein.
Wartung Prüfen Sie: Durch defekte Toranlagen bzw. Sicherheitsein- richtungen besteht Verletzungsgefahr. Alle Schraubenverbindungen auf festen Sitz Zu Ihrer Sicherheit sollten Sie die empfohlenen Kabel auf Beschädigung Wartungsintervalle für Ihre Toranlage inkl. aller Federn und Befestigungsteile Sicherheitseinrichtungen einhalten. Es besteht Verletzungsgefahr durch die sehr Wartungsintervall: stark gespannten Torfedern.
Fehlerbehebung Fehler Ursachen Lösung Der Antrieb funktioniert nicht. 1. Der Stecker ist nicht sicher 1. Netzstecker in Steckdose eingesteckt. stecken. 2. Die Sicherung hat ausgelöst. 2. Ursache von einem Techniker prüfen lassen, danach die Sicherung wieder einschalten. Der Handsender kann den Antrieb 1.
EG-Konformitätserklärung Die Garagentorantriebe der Serie RolloPort SX5 (Art.- Nr.: RP-SX5-900N-1 / RP-SX5-900N-2) erfüllen die Anforderungen der folgenden Richtlinien und Normen: 2006/42/EG Maschinenrichtlinie EN 12445:2000 (EN 13241-1:2003) EN 12453:2000 (EN 13241-1:2003) 2006/95/EG Niederspannungsrichtlinie EN 60335-1 + A13:2008 + A14:2010 EN 60335-2-95:2004 2004/108 EG EMV-Richtlinie EN 50366/A1:2006EN 62233:2008...
Garantiebedingungen Innerhalb der Garantiezeit auftretende Mängel besei- RADEMACHER Geräte-Elektronik GmbH & Co. KG gibt tigt RADEMACHER kostenlos entweder durch Reparatur eine 36-monatige Garantie für Neugeräte, die entspre- oder durch Ersatz der betre enden Teile oder durch chend der Einbauanleitung montiert wurden. Von der...
Seite 38
RADEMACHER Geräte-Elektronik GmbH & Co. KG Buschkamp 7 46414 Rhede (Deutschland) info@rademacher.de www.rademacher.de Service: Hotline 01805 933-171* Telefax +49 2872 933-253 service@rademacher.de * 14 ct/Minute aus dem deutschen Festnetz der DT AG/ Mobilfunk max. 42 ct/Minute (gilt nur für Deutschland)
Seite 39
Einbau- und Bedienungsanleitung für den Garagentorantrieb RolloPort SX5 ......1 Installation and Operating Instructions for RolloPort SX5 Garage Door Opener .......39 Item no: RP-SX5-900N-3 (3-piece rail) / RP-SX5-900N-1 (1-piece rail) VBD 583-1-D-EN-(07.11)
CE Mark and Conformity you have decided for a quality product manufactured This present product complies with the requirements by RADEMACHER. We would like to thank you for of the applicable european and national directives. your con dence. The conformity has been proved and the correspon-...
Seite 41
Remove the door locks ..........49 recognition (power limiting) ........71 Take measurements ..........50 Technical Speci cation ..........72 Assembly of the rails (for RP-SX5-900N-3 only) ..51 Technical Data ............72 Tension the toothed belt .........51 Trouble shooting .............73 Connect the door opener housing to the rail ...52 EC declaration of conformity ........74...
6 x Wall plug (10 mm) 6 x Hexagon head screw (8 x 60 mm) 1 x Spike 2 x Mounting strap – RP-SX5-900N-3 3-piece rail + two connectors – RP-SX5-900N-1 1 piece rail, without connector 1 x Radio code switch RP-SX5-CSG-AF26 (for RP-SX5-900N-3 only)
Correct use Use the garage door opener only: Correct use of the hand transmitter to open and close garage doors The remote control via hand transmitter is only admis- sible for appliances and equipment in which radio for private use interference in the transmitter or receiver does not according to the instructions and safety present a hazard for persons, animals or property or...
Admissible garage door types swing out standard up-and-over doors sectional doors The doors must move smoothly and comply with the regulations of the following standards: EN 12453 and EN 12604. Up-and-over doors Ceiling sectional doors Inadmissible types of garage door Doors which require tilting and rotating move- Non swinging out re- ments may not be operated with the type SX5...
General safety instructions Important safety instructions Never reach into the moving door or into moving parts. CAUTION For your safety and the safety of others, it is Instruct all persons who operate the garage door essential that you follow these instructions in the safe use of the equipment.
Functional description Intelligent microcomputer Automatic closing function Intelligent, computerized, exact positioning of travel, The automatic closing time of the door can be set prompt power determination, reverses if obstructions from 30 to 240 seconds (refer to page 62/63). are met. 2000 cycle alarm Drive When the opener has run 2000 cycles, it will beep...
Functional description/emergency release In the event of a power cut, the door can be operated manually by pulling the emergency release cable. There is a risk of injury. The door can fall un- controllably when it is released (e. g. if springs are weak or broken, or if the door is not properly balanced).
Required tools You require the following tools. Remove the door locks Remove all vertical and horizontal door locks and catches. IMPORTANT! Keep the „old“ door locks in a safe place. In the event that you should remove the garage door opener, you will have to t these again in order to restore the original state of the door.
Take measurements Measure up and mark the centre of the door. Mark the centre of the door, as shown, on the upper edge of the door, on the door lintel and on the garage ceiling. Determine the distance between the top edge up-and-down of the door and the ceiling.
Assembly of the rails (for RP-SX5-900N-3 only) NOTE The RolloPort SX5 is supplied with three rails: two end pieces, including a pre-assembled toothed belt. a middle piece (without toothed belt) with two connectors. Lay the two end pieces with the pre-assembled...
Connect the door opener housing to the rail First of all insert the connector (5). IMPORTANT Ensure that the microswitch (3) is not damaged when Place the rail (4) with the inboard chain sprocket mounting the rail. (supplied pre-assembled in the rail) over the connector (5).
Seite 53
Connect the door opener housing to the rail Alternative installation of the drive transversely to the rail. IMPORTANT Mortal danger due to electric shock when The microswitch (3) must always be positioned at the undertaking any work on the microswitch (3). end of the rail.
Attachment of the door opener and the rail A / B / C / D refer to the following pages Installation on the lintel The installation should preferably be on the lintel, Installation as this means that the forces encountered can best on the min.
(A) Installation of the header bracket (1) NOTE The header bracket (1) must be aligned with the mid- point of the door. Mark out the position of the header bracket (1) and drill the mounting holes (e. g. with a 10 mm 1 = Header bracket masonry drill bit).
(C) Installation of the door bracket (8) NOTE We recommend xing the door bracket (8) to the door frame if possible. For plastic or thin-walled wooden doors, additional cross-beams are necessary in order to avoid damag- ing the door. In this case, consult your door supplier. Use existing drillholes, if possible, to mount the door bracket (8).
(C) Installation of the door bracket (8) Screw the door bracket (8) tight with the en- closed self-tapping hexagon screws (8 x 15 mm). Finally, x the door connector (12) to the door bracket (8) with the enclosed bolt (9). NOTE A straight door connector is supplied pre-assembled, and this is permanently xed to t he rail.
Important notes after installation After installation, ensure that the mechanism After installation, ensure that the drive prevents is properly adjusted and that the drive reverses or stops the opening movement when the door is when the door contacts a 50 mm high object loaded with a mass of 20 kg, xed centrally on the placed on the oor (for drives incorporating an bottom edge of the door.
Setting limits / setting the upper limit Carrying out the instructions in the wrong Correct setting order: order when setting the limits will result in 1. Set upper limit malfunctions. Be sure to keep to the setting 2. Set lower limit order speci ed.
Carry out reference run for power measurement During the reference run there is a risk of in- jury, as the door opener develops extremely strong forces. 1. Press „+“, the 2. Press „P“, 3. The door goes up display shows „3“. „3“...
Adjust power limiting as required NOTE If the power level is too low, the door move- The door opener is preset to stage 3 by the supplier. ment will be impaired, particularly if the If required (e. g. if the power level is too low) you mechanical structure of the door is not well can subsequently adjust the power limiting setting.
Alarm setting If the alarm is switched on, the door opener To end the beeping: beeps if the door is open for longer than 10 Press the door control button to fully close the door. minutes. The door opener beeps for 30 seconds every 10 minutes.
Automatic closing time setting 4. Press „+“ and select 5. Press „P“ in order 6. Conclude programming the required closing to store the setting. (refer to page 66, me- time: thod 2) or proceed with the next setting. 1 = 30 sec. 5 = 150 sec.
Opening speed setting With this function you can set the speed of the upwards Configuration of the opening speed is set in cm/s movement to your individual requirements. (centimetres per second). 1. Press „+“. 2. Press „P“, 3. Press „+“ or „–“ and the display is „1“.
Back-jump Function setting After closing, the jump-back function relieves the drive components by brie y moving in the opposite direction (10 cm). 1. Press „+“ . 2. Press „P“, 3. Press „+“, the display is „0“. the display is „1“. (press several times if necessary) until „9“...
Conclude programming IMPORTANT NOTE Please note: this concluding step must be carried You can conclude the programming in two ways: out, otherwise the information stored will be lost. Method 1: Carry out this method without fail after the reference run. 1.
Registering and de-registering hand transmitters Registering hand transmitters: 1. Press „S“ for approx. 2. The ten digit of 3. Press any key twice on 3 seconds and then display is „0“. the hand transmitter. let go. „0“ turns o and the hand transmitter is registered.
Connecting additional electrical equipment When working on electrical systems there is a If the external buttons are not connected risk of danger to life due to electrocution. properly, the operational safety of the equip- ment is at risk. The connection of additional electrical equipment must only be carried out by a quali ed electrician.
Manual door operation In the case of power failure: If you wish to manually operate the door in There is a risk of injury. The door can fall down the event of a power cut, you must pull the uncontrollably when released (e. g. if the door emergency release cable so that this releases is not balanced) the door from the door opener.
Instructions for the user Notes for use. When the power is back, you can operate the hand transmitter or the wall panel, and the emergency Check the opener system to determine whether release will engage automatically. it moves smoothly the rst time the garage door opener is used.
Maintenance Defective door systems and safety equipment Check: result in the risk of injury. All screw connections to ensure they are tight For your safety, you should comply with the Cables for damage recommended maintenance intervals for your Springs and xing parts door system, including all safety equipment.
Voltage (V) Door size (m Admissible ambient temperature (°C) RP-SX5-900N-1 230 V / 50 Hz 12,5 –10 ... + 40 RP-SX5-900N-3 Guide rail and available sizes Item no. Total length Height of travel Lifting height RP-SX5-900N-1 3320 mm 2500 mm <...
Trouble shooting Error Causes Solution The door opener does not work. 1. The plug is not inserted 1. Plug the mains plug into the properly. mains outlet. 2. The fuse has been tripped. 2. Have the cause checked by a quali ed person, then switch the fuse back on again.
EC declaration of conformity Garage door openers of series RolloPort SX5 (Item no. RP-SX5-900N-1 / RP-SX5-900N-2) ful l the require- ments of the following guidelines and standards: 2006/42/EG Machinery directive EN 12445:2000 (EN 13241-1:2003) EN 12453:2000 (EN 13241-1:2003) 2006/95/EC Low-voltage directive EN 60335-1 + A13:2008 + A14:2010 EN 60335-2-95:2004 2004/108 EG...
Any defects occurring within the period of guarantee rants all new devices for 36 months, that have been will be recti ed by RADEMACHER at no cost either installed in accordance with the installation manual. by repairing or replacing the parts concerned or...
Seite 76
RADEMACHER Geräte-Elektronik GmbH & Co. KG Buschkamp 7 46414 Rhede (Germany) info@rademacher.de www.rademacher.de Service: Hotline 01805 933-171* Telefax +49 2872 933-253 service@rademacher.de * 14 ct/minute on a German landline operated by DT AG/ Mobile charges max. 42 cents/minute (Germany only)