SAGEMCOM D18V Bedienungsanleitung Seite 165

D16V/D18V/D21V
11.7. 15.2.2. Telephone
Deleting messages
11.7.1. Deleting the current message
During the playback of the message, press the
No dial tone
The message in progress is deleted:
- If you have other messages, the next message is broadcast.
- Otherwise, the answering machine returns to standby mode.
11.7.2. Deleting all messages already played back
1. In standby mode, hold down the
This beep informs you that all your messages already played back have been deleted.
- OR -
1. Press
2. Select "delete all" using the
3. Press
A beep indicates that all messages already played back have been deleted.
Dial tone is OK, but can't dial out
12. Answering machine setup
Handset does not ring
12.1.
Number of rings
This parameter enables you to set the number of times your telephone rings before the
answering machine answers a call. The number of rings can be set between 2 and 7.
You can also select the "ECONOMY"mode. The "ECONOMy" mode automatically determines the
number of rings: If there are no new messages on the answering machine, the number of rings
You experience static, noise or fading in
will be 4, otherwise the number of rings will be 2.
and out
1. Press
2. Select "settings" using the
3. Select "ring delay" using the
15.3.
Unit beeps
4. In the list, select the desired number of rings (between 2 and 7) using the
- Place handset in base for 20 seconds to reset the security code. If that doesn't work,
the "ECONOMy" mode, Press
charge battery for 15 hours.
12.2.
Remote access to answering machine
- Clean charging contacts on handset and base with a soft cloth.
- See solutions for «No dial tone».
Your answering machine can be interrogated remotely. This function lets you play back your
- Replace battery.
messages and set up your answering machine from another telephone located outside your
home.
15.4.
Memory dialling
- Did you program the memory location keys correctly?
12.2.1. Activate/deactivate remote access
- Did you follow proper dialling sequence?
- Make sure the tone/pulse setting is correct.
1. Press
- Did you reprogram numbers into memory after power outage or battery replacement.
2. Select "settings" using the
3. Select "remote acc." using the
4. Use or
5. Press
Problem
. Select "answ machine "using the
or
to confirm deletion.
. Select "answ machine " using the
or
or
.
. Select "answ machine " using the
or
or
to select "activate" or " deactivate " setting.
key to confirm your selection. You will hear a confirmation tone
Check installation:
key.
- Is the base power cord connected to a
working outlet?
- Is the telephone line cord connected to the
base unit and the wall jack?
Disconnect the base from the wall jack and
connect another phone to the same jack. If
key until you hear a beep.
there is no dial tone in the second phone, the
problem might be your wiring or local service.
Is the handset out of range of the base?
Make sure the battery is properly charged
or key, press
(12 hours).
key, press Is the battery pack installed correctly? .
Did the IN USE indicator come on?
The battery may need to be charged.
Make sure the tone/pulse setting is correct.
Make sure the RINGER setting on the
handset is programmed to ON.
You may have too many extension phones on
your line. Try unplugging some phones.
See solutions for «NO dial tone».
Is handset out of range?
Move closer to the base.
Does the base need to be relocated?
Charge battery.
or key, press
Make sure base is not plugged into an outlet
key, press .
with another household appliance.
key, press .
or key, press
key, press .
key, press .
- 24 - - 21 -
English
Solution
.
.
or key or
.