Ethernet / Lan - WolfVision VZ-9 Bedienungsanleitung

Ethernet / LAN

The LAN connection (10BASE-T/100BASE-TX) can be used for controlling the VZ-9 over a
computer network. Image transfers, firmware updates and displaying status information is
possible. In addition units with serial numbers largen then 095501 can send out e-mail
notifications.
The following protocols are supported: TCP/IP, ICMP and ARP.
Supportet Browsers are Internet Internet Explorer, Netscape Navigator and Mozilla.
By default, DHCP is activated to receive all settings automatically.
Image Transfer Resolution: Still Image: 1024x768 (or 512x384), Live Image: 160x120
Please check the separate ETHERNET / LAN description on our internet homepage at:
www.wolfvision.com/support
DVI PORT
Pin 8
Pin 1
Pin 9
Pin 17
Pin 24
USB-PORT
The WolfVision USB-software can be found on the supplied CD-ROM. Please check our
Internet homepage at: www.wolfvision.com/support if an update of this software is available
as a free-download. The software works under Windows 98/ME/2000/XP. Windows 95 and NT
will not work, because they do not support USB.
Serial control input, RS 232
The serial port can be used to control the Visualizer through an external device, like a remote
control system for a complete conference room.
3 4
1 2 5
9-pin D-Sub connector
on unit; male
(front side)
6 7 8 9
The complete serial protocol can be found on our internet homepage:
Changing the lamp of the Visualizer
1. Remove the power cord of the Visualizer.
2. Remove the safety screw by using the supplied Allen key. (if available)
3. Remove the lamp cover itself by turning the case.
4. Change the lamp (lift the safety ring before). Place the new lamp very carefully into the socket.
CAUTION: LAMP CAN BE HOT!
5. Mount the lamp cover in reverse order (3. to 1.) and set the safety screw.
Lamp type: 4642 halogen lamp 12V/35W incl. heat shield and mounting ring.
4000 h average burning life
:
(or on the supplied CD-Rom).
1 - T.M.D.S. Data2-
2 - T.M.D.S. Data2+
3 - T.M.D.S. Data2/4 Shield
4 - T.M.D.S. Data4- (*)
C1 C2
5 - T.M.D.S. Data4+(*)
6 - DDC Clock
7 - DDC Data
C3 C4
C5
8 - Analog Vertical Sync (**)
C1 - Analog Red (**)
C4 - Analog Horizontal Sync (**)
C5 - Analog Ground (**)
(analog R, G & B return)
The USB 2.0 output of the VZ-9 can be used to capture and
transfer Visualizer images onto a computer in a fraction of a
second. No additional computer hardware (like a grabber card)
is required. In this way the Visualizer can be used as a 3-D
scanner for your computer. Just connect the USB port (#19) of
the Visualizer and the USB port of your computer, using the
supplied USB cable. The software is fully twain compatible. The
USB 2.0 output is fully USB 1.1 compatible (less speed).
Pins:
Baud rate: 9200, 19200, 38400, 57600 or 115200 (selectable)
Please note that DecimaI-Codes (=ASCII-Codes or Hex-Codes)
must be sent as one single byte (e.g. 199 and not: 1 + 1 + 9) !
9 - T.M.D.S. Data1-
10 - T.M.D.S. Data1+
11 - T.M.D.S. Data1/3 Shield
12 - T.M.D.S. Data3- (*)
13 - T.M.D.S. Data3+ (*)
14 - +5V Power
15 - Ground (return for +5V,
HSync and Vsync)
16 - Hot Plug Detect
C2 - Analog Green (**)
**...not available on units with serial number lower than 095500
2: RX, 3: TX, 5: GND, 7: RTS, 8: CTS
databits: 8, stopbit: 1, parity: no
www.wolfvision.com/support
12
17 - T.M.D.S. Data0-
18 - T.M.D.S. Data0+
18 - T.M.D.S. Data0+
19 - T.M.D.S. Data0/5 Shield
20 - T.M.D.S. Data5- (*)
21 - T.M.D.S. Data5+ (*)
22 - T.M.D.S. Clock+
23 - T.M.D.S. Clock-
24 - Analog Vertical Sync (**)
C3 - Analog Blue (**)
*...not used