Faderstart; Sleep Mode; End Of Operation - Omnitronic DMS-1150 Bedienungsanleitung

Overview over the effect-parameters:
Effects Parameter PT
Adjustable value
Skid 0-9990 ms
Filter 0-9990 ms
Phase 0 - 9900 ms
Echo 0 - 2000 ms
Flanger 0 - 9990 ms
Trans 0 - 9900 ms
Pan 0 - 9990 ms
Reverse -1000 - 1000 ms
6.12 Beat Sync-function
(1) You can either adjust the effect-time via the Parameter Time-control or more comfortably via the Presets
of the Beat Sync-function.
(2) Example: Press the Auto BPM-button during playback and wait until the display shows the current value.
Press the Echo-button. Adjust the Parameter Time-control and watch the Beat Sync-LEDs. When the
Echo-time corresponds to a whole note, the 1/1 LED is lit. This way, the Beat Sync-LEDs show the most
common time adjustments.
(3) Via the Beat Sync-buttons, you can quickly and easily select the desired tact.

6.13 Faderstart

With the DMS-1150, you have the possibility to start the CD-player directly from the mixer. Make sure that
the Relay-socket is connected with the respective socket on the mixer. Additionally, the Audio Out-sockets
have to be connected with the Line-input sockets of your mixer. Please note that the Faderstart-function only
works with the appropriate mixers. Insert the CD and select the desired track (Pause-mode). Start playback
from your mixer.
Please note that the Faderstart-function is a Cue-point Faderstart-function. This means that the CD-player
starts playback after activating the respective channel of the mixer and goes into Pause-mode and returns to
the Cue-point after activating the channel again.
(1) Prerequisites for the Faderstart-operation
The mixer has to be connected via a 3.5 mm mono jack with the CD-player. For starting the playback, the
jack's positive pin (tip) is to be connected with the audio mass via a short impulse. For pausing the playback,
the jack's negative pin (sleeve) is to be connected with the audio mass via a short impulse. The mixer has to
be equipped with a switch, button or fader that will connect the tip with the audio mass for starting the
playback and the sleeve for pausing the playback when the respective channel is activated.
(2) Relay-function
In the Relay-operation, the device automatically switches to the other player after every track. In this way,
you have the possibility to enlarge the music program by using several CDs.
Connect the Relay-sockets of the two CD-players with one another. Choose Single or Continuous via the
SGL/CTN-button. The playback switches from one player to the other.
Example:
Press the Single-button (The display shows "SINGLE") on both CD-players. Start playback of CD1. As soon
as the current track of CD1 is finished, the player automatically starts CD2. The first CD-player goes into
Pause-mode. You can enter a new CD or memorize a Cue-point at the respective player in the Pause-Mode.

6.14 Sleep mode

If the player mechanism is set to pause for a period exceeding 30 minutes, the unit will automatically step
into sleep mode. The display indicates „SLEEP" and all illuminated buttons and all LEDs are extinguished.
Press any button, to exit sleep mode.

6.15 End of operation

Before you switch off the device, please make sure that no CD remains in the player. All memorized Cue-
points, samples and effect-parameters are stored inside the CD-player and can be recalled after switching
the CD-player off.
Default value Adjustable value
10 ms 0 - 9990
6000 ms 0 - 255
300 ms 0 - 255
350 ms 0 - 255
1000 ms 0 - 255
0 - 255
450 ms
0 ms
32/64
Parameter PR
Default value
10
0
0
128
179
153
10602426_V_1_0.DOC