Operation - Panasonic EY6220 Betriebsanleitung

P05-11(EY6220EN).qxd 10.7.6 16:49 ページ 6
B536502_EY6220_Tori_EU

OPERATION

Hexagonal driving shaft···(A)
NOTE: When attaching or removing bit, be
sure to set the main switch lock at the
lock position.
Select the suitable bit and lightly push it into
the hexagonal driving shaft of the main unit.
(Refer figure 2)
Refer figure 2 for useable bits.
E
Clutch handle···(B)
When using the tool for driving screws into
soft material or for terminal screws, etc., there
is the possibility of damaging the material or
threads if the torque is too high. To
compensate for this, the clutch torque may be
adjsuted by turning the clutch handle to the
required setting.
Clutch position 1 is the minimum and the
clutch torque increases with positions 2, 3, 4,
and 5. When the device is set at position 6,
the clutch will not slip and the connection to
the motor will be direct.
CAUTION: If the battery pack loses its power
during usage, the clutch may not
slip even at positions 4 or 5, if this
occurs, recharge the battery pack.
(Refer figure 3)
Bit locking function
With the switch at off, the bit is locked in place,
and the tool can be used as a manual screw-
driver.
There will be a little play in the driving shaft,
but this is not a malfuncton.
CAUTION: Exact torque should be verified
with a torque wrench for precise
limits as the screw can be
damaged.
(Refer figure 4)
Refine_EY6220.06.p1.pdf
Refine_10-08-18 10:30:43
Main switch (ON/OFF)···(E)
Push the upper half of the switch for forward
( ) rotation, or the lower half for reverse
( ) rotation.
(Refer figure 5)
Speed selector switch···(C)
To suit the application of this tool, two
different rotational speeds are available.
Depending upon use, either the high or low
speed should be selected.
LOW strong torque
200min -1 (RPM)
HIGH less torque
400min -1 (RPM)
CAUTION: Check rotational speed selection
before operating this tool.
(Refer figure 6)
Main switch lock···(D)
After use, set the main switch lock at the lock
position to prevent accidental operation.
(Refer figure 7)
Battery pack (EY9221)···(F)
Appropriate Use of Battery Pack
Ni-MH Battery Pack
• Charge the Ni-MH battery fully before
storage in order to ensure a longer service
life.
• The ambient temperature range is between
0˚C (32˚F) and 40˚C (104˚F). If the battery
pack is used when the battery temperature
is below 0˚C (32˚F), the tool may fail to
function properly. In that case, charge the
battery until charging is completed for
appropriate functioning of the battery.
• When battery pack is not in use, keep it
away from other metal objects such as
paper clips, coins, keys, nails, screws, or
other small metal objects that can make a
connection from one terminal to another.
Short-circuiting the battery terminals
together may cause sparks, burns or a fire.
• When operating with a Ni-MH battery pack,
make sure the area is well ventilated.
Battery Pack Life
The rechargeable batteries have a limited life.
If the operation time becomes extremely short
after recharging, replace the battery pack with
a new one.
6
P05-11(EY6220EN).qxd 10.8.18 13:39 ページ 7
4 10-08-23 15:56:41
Battery Recycling
ATTENTION: For environmental protection
and recycling of materials, be
sure that it is disposed of at an
officially assigned location, if
there is one in your country.
Battery charger (EY0L11)···(H)
Charging
Common Cautions for the Li-ion/Ni-MH Battery
Pack
NOTE: • When a cold battery (of about 0˚C or
less) is to be charged in a warm
room, leave the battery in the room
for at least one hour and charge it
when it has warmed up to room
temperature. (Failing to do so may
result in less than a full charge.)
• Cool down the charger when
charging more than two battery
packs consecutively.
• Do not insert your fingers into
contact hole, when holding charger
or any other occasions.
• When charging continuously, wait
about 5 seconds after removing one
battery pack before inserting the
next.
CAUTION: To prevent the risk of fire or
damage to the battery charger.
• Do not use power source from
an engine generator.
• Do not cover vent holes on the
charger and the battery pack.
• Unplug the charger when not in
use.
Li-ion Battery Pack
NOTE: Your battery pack is not fully charged
at the time of purchase. Be sure to
charge the battery before use.
Ni-MH Battery Pack
NOTE: When you charge the battery pack for
the first time, or after prolonged
storage, charge it for about 24 hours to
bring the battery up to full capacity.
Battery charger
1. Plug the charger into the AC outlet.
NOTE: Sparks may be produced when the
plug is inserted into the AC power
supply, but this is not a problem in
terms of safety.
Refine_EY6220.07.p1.pdf
Refine_10-08-18 16:12:10
2. Select the current battery dock (Li-ion Battery
pack or Ni-MH Battery pack) cover. Slide the
battery dock cover to allow insertion.
3. Insert the battery pack firmly into the charger.
Pictured:
Ni-MH Battery Pack
%
To AC
outlet
$
#
4. During charging, the charging lamp will be lit.
When charging is completed, an internal
electronic switch will automatically be triggered
to prevent overcharging.
• Charging will not start if the battery pack is
warm (for example, immediately after heavy-
duty operation). The orange standby lamp will
be flashing until the battery cools down.
Charging will then begin automatically.
5. The charge lamp (green) will flash slowly once
the battery is approximately 80% charged. (Li-
ion Battery Only)
6. When charging is completed, the charging lamp
in green color will turn off.
7. If the temperature of the battery pack is 0˚C or
less, charging takes longer to fully charge the
battery pack than the standard charging time.
Even when the battery is fully charged, it will
have approximately 50% of the power of a fully
charged battery at normal operating
temperature.
8. Consult an authorized dealer if the charging
lamp (green) does not turn off.
9. If a fully charged battery pack is inserted into
the charger again, the charging lamp lights up.
After several minutes, the charging lamp in
green color will turn off.
7