Messages; Disc And Card Handling; Maintenance - Yamaha BD-S2900 Bedienungsanleitung

The following messages or service numbers appear on the television or unit's display when something unusual is detected during startup and use.
■ On the television
Cannot play.
Cannot play on this unit.
No disc
This operation is currently disabled.
■ On the unit's display
F99
HDMI ONLY
No PLAY
No READ
PLEASE WAIT
UNFORMAT
UNSUPPORT
U59
U72
U73
H or F

DISC AND CARD HANDLING

Clean discs
DO DO NOT
Wipe with a damp cloth and then wipe dry.
Disc and card handling precautions
• Handle discs by the edges to avoid inadvertent scratches or fingerprints on
the disc.
• Do not attach labels or stickers to discs (This may cause disc warping,
rendering it unusable).
• Do not write on the label side with a ball-point pen or other writing
instrument.
• Do not use record cleaning sprays, benzine, thinner, static electricity
prevention liquids or any other solvent.
• Do not use scratch-proof protectors or covers.
• Clean any dust, water, or foreign matter from the terminals on the rear
side of the card.
• Do not use the following discs:
– Discs with exposed adhesive from removed stickers or labels (rented discs etc).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes.

MESSAGES

• You inserted an incompatible disc.
• You tried to play a non-compatible image.
• Confirm "SD" on the unit's display is not blinking and re-insert the card.
• The disc may be upside down.
• The operation is prohibited by the unit or disc.
• The unit fails to operate properly. Press [STANDBY/ON] on the main unit to switch the unit
to standby for 3 seconds. Now press [STANDBY/ON] on the main unit again to turn the
unit on.
• Some BD-Video discs can only be output with HDMI.
• There is a viewing restriction on a BD-Video or DVD-Video.
• The disc is dirty or badly scratched. The unit cannot play.
• Displayed when the unit is started and turned off. This is not a malfunction.
• The unit is carrying out its recovery process. You cannot operate the unit while "PLEASE
WAIT" is displayed.
• You inserted an unformatted DVD-RAM, DVD-RW, DVD+RW, an unused DVD+R,
DVD+R DL or DVD-RW (DVD-Video format).
• You have inserted a disc the unit cannot play.
• The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the message
disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
• The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– Please use HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is damaged.
• There is something unusual. (The service number displayed after H and F depends on the
unit's condition.)
• Check the unit using the troubleshooting guide. If the service number does not disappear, do
the following.
1 Disconnect the plug from the household mains socket, wait a few seconds, then reconnect
it.
2 Press [STANDBY/ON] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request service from the
dealer. Inform the dealer of the service number when requesting service.
Clean this unit with a soft, dry cloth
• Never use alcohol, paint thinner or benzine to clean this unit.
• Before using chemically treated cloth, carefully read the instructions that
came with the cloth.
Observe the following points to ensure continued listening
and viewing pleasure.
Dust and dirt may adhere to the unit's lens over time, making it impossible to
play discs.
Do not use any lens cleaners as they may damage the unit.

MAINTENANCE

REFERENCE
Page
2, 3
15
–
–
–
–
–
19
–
–
–
–
2, 3
–
–
–
24-26
27
En