Beam - Yamaha YSP-500 Bedienungsanleitung

Continued from the front
3
Carry out the AUTO SETUP (IntelliBeam)
Carry out the AUTO SETUP to adjust the settings that best match your
listening environment
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment.
during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
1
Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC
jack on the front panel.
You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam
microphone on top of it as shown below.
1 2
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON
INTELLIBEAM MIC
IntelliBeam microphone (supplied)
Cardboard microphone stand (supplied)
2
Set the IntelliBeam microphone at your normal listening position.
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would
be when you are seated.
IntelliBeam
Upper bound
microphone
position of the
microphone
Center height of
this unit
Within 1 m
(3.3 ft)
Within 1 m
(3.3 ft) Center line
Cardboard
Listening
IntelliBeam
Cardboard
microphone stand
position microphone
microphone
More than 1.8 m (6.0 ft) Lower bound position stand
of the microphone
3
Press STANDBY/ON on the
4
Turn on the power of your TV.
remote control.
The power of this unit turns on.
Before operations, insert batteries into the remote control
(see page 26 in the Owner's Manual).
If necessary, adjust the volume level of this unit.
If you have connected the subwoofer, set the volume and 5 Select the appropriate video
crossover/high cut frequency. Refer to the note on page
32 in the Owner's Manual. input on your TV.
"YSP-500" appears on your TV. If the OSD video pin cable
Subwoofer
is connected to the video input 1 on the TV as shown in the
CROSSOVER/
VOLUME
connection example, switch the video input to "1".
HIGH CUT
STANDBY/ON POWER POWER
AV TV
MIN MAX MIN MAX
6 Set the operation mode selector
to YSP.
This unit switches to the YSP operation mode.
It is normal for loud test tones to be output
CH LEVEL
ENTER
TEST
7
Press and hold AUTO SETUP for
3 4
more than 2 seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the OSD video
pin cable (see the connection example on the front page).
TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP

5BEAM

ST+3BEAM 3BEAM
1 2 3
8 Check the following points.
About the IntelliBeam microphone
Place the IntelliBeam microphone on
• Is the microphone placed on an imaginary center line drawn
the extended center line of this unit
from this unit?
and 1.8 m (6.0 ft) or more away from
• Is the microphone placed within 1 m (3.3 ft) upper or lower
it. Also, make sure place the
from the center height of this unit?
IntelliBeam microphone within 1 m
(3.3 ft) upper or lower from the center
• Is the microphone placed more than 1.8 m (6.0 ft) from the
height of this unit.
front of this unit?
About the room environment
• Is your listening room kept as quiet as possible?
9 Prepare to leave the room.
The best setting may not be done if you are in the room.
Prepare to leave the room in 10 seconds after pressing
ENTER in step 10.
y Hint
• When leaving the room, bring this guide with you.
• Wait outside the room during the AUTO SETUP procedure.
• The AUTO SETUP procedure takes
• To cancel the AUTO SETUP procedure after it is started,
press RETURN.
10 Press ENTER to start the AUTO
SETUP procedure, and then
leave the room within 10 seconds.
The following screen appears on the TV. Leave the room
within 10 seconds before the AUTO SETUP procedure
starts.
MENU
TV/AV
YSP CH LEVEL MENU
AUTO SETUP START
RETURN
Will begin in 10sec
TV/AV Please leave the room
ENTER
YSP
**--------
[RETURN]:Cancel
TEST RETURN
The setup screen automatically changes during the AUTO
SETUP procedure.
When the AUTO SETUP procedure is completed, the
following screen appears on the TV.
SHOW RESULT
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
AUTO SETUP SUBWOOFER :NOT APPLICABLE
PREPARATION & CHECK
[ENTER]:Save set-up
Please connect the MIC.
[RETURN]:Do not save set-up
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min. If "ENVIRONMENT CHECK (FAILED) is displayed, see page
After [ENTER] is pressed,
please leave the room. 36 in the Owner's Manual and then run the procedure again.
[ENTER]:Start [RETURN]:Cancel
y Hint
• The result may differ depending on the environment.
• If any error occurs, the corresponding error message appears
on the screen. In this case, see "Error messages for AUTO
SETUP" on page 37 in the Owner's Manual and then follow
the instructions. To start the AUTO SETUP procedure once
again, press RETURN.
11 Press ENTER.
The following screen appears on the TV for 2 seconds and
then the menu screen disappears from the TV.
CH LEVEL MENU
AUTO SETUP COMPLETE
Please remove the MIC from
TV/AV
the YSP and the listening
ENTER
position.
YSP
TEST RETURN
about 3 minutes.
12 Disconnect the IntelliBeam
microphone.
The AUTO SETUP has completed. Keep the IntelliBeam
microphone in a safe place.
The settings are automatically saved in the system memory.
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON
INTELLIBEAM MIC
4
Enjoying surround sound
Enjoy TV or DVD digital audio in surround sound.
For instructions on how to operate or set your TV or DVD player, refer to the owner's manual supplied with each component.
Enjoying DVDs in surround sound Enjoying TV in surround sound
1 Select the DVD video input on 1 Select the TV channel using the
your TV. remote control supplied with
your TV.
2 2
Set the operation mode selector Set the operation mode selector
to YSP.
to YSP.
This unit switches to the YSP operation mode. This unit switches to the YSP operation mode.
TV/AV
ENTER
YSP
TEST RETURN
3 1) Press DVD on the remote 3 Press TV on the remote control
control of this unit. of this unit.
This unit switches to the TV playback mode.
This unit switches to the DVD playback mode.
STB VCR DVD AUX
TV
INPUT1 INPUT2 MACRO
TV
2) Play back the supplied demonstration
DVD on the DVD player.
4
Check the multi-channel digital signal being output at this unit.
The MULTI indicator and/or (see page 42 in the Owner's Manual) is lit in the front panel display.
output from your TV speakers, mute the volume on your TV. For details about digital audio input signals, see
page 46 in the Owner's Manual.
5 Press VOLUME +/- on the remote control to adjust the volume
level of this unit.
6
Press one of the beam mode buttons on the remote control
to select the desired beam mode.
Select one of the six beam modes that best matches the current input source of this unit.
For further information on the beam modes, see page 44 in the Owner's Manual.
To fine-tune the listening environment parameters manually or make advanced settings for speaker positions,
sound beams, etc., see "MANUAL SETUP" on page 56 in the Owner's Manual.
TV/AV
ENTER
YSP
TEST RETURN
STB VCR DVD AUX
TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM ST+3BEAM 3BEAM
1 2 3
MULTI indicator
If the sound is
VOLUME CH TV VOL
MUTE TV INPUT TV MUTE
5BEAM ST+3BEAM 3BEAM
1 2 3
STEREO MY BEAM MY SUR.
4 5 6