Siemens sinamics g120C Handbuch Seite 42

Inbetriebnehmen
4.2 Weitere Einstellungen
P-No. Note
6 20
p8623 CAN Bit Timing selection [hex]
p8630 CAN Virtuelle Objekte
p8641 CAN Abort Connection Option Code
0 Keine Reaktion
2 AUS2
r8680 CAN Diagnosis Hardware
p8684 CAN NMT Zustand nach Hochlauf
p8685 CAN NMT Zuständ
p8699 CAN RPDO Überwachungszeit [ms]
p8700 CAN Receive PDO 1 [hex]
p8701 CAN Receive PDO 2 [hex]
p8702 CAN Receive PDO 3 [hex]
p8703 CAN Receive PDO 4 [hex]
p8704 CAN Receive PDO 5 [hex]
p8705 CAN Receive PDO 6 [hex]
p8706 CAN Receive PDO 7 [hex]
p8707 CAN Receive PDO 8 [hex]
p8710 CAN Receive Mapping für RPDO 1 [hex]
p8711 CAN Receive Mapping für RPDO 2 [hex]
p8712 CAN Receive Mapping für RPDO 3 [hex]
p8713 CAN Receive Mapping für RPDO 4 [hex]
p8714 CAN Receive Mapping für RPDO 5 [hex]
p8715 CAN Receive Mapping für RPDO 6 [hex]
p8716 CAN Receive Mapping für RPDO 7 [hex]
p8717 CAN Receive Mapping für RPDO 8 [hex]
p8720 CAN Transmit PDO 1 [hex]
p8721 CAN Transmit PDO 2 [hex]
p8722 CAN Transmit PDO 3 [hex]
p8723 CAN Transmit PDO 4 [hex]
p8724 CAN Transmit PDO 5 [hex]
p8725 CAN Transmit PDO 6 [hex]
p8726 CAN Transmit PDO 7 [hex]
p8727 CAN Transmit PDO 8 [hex]
p8730 CAN Transmit Mapping für TPDO 1 [hex]
p8731 CAN Transmit Mapping für TPDO 2 [hex]
p8732 CAN Transmit Mapping für TPDO 3 [hex]
p8733 CAN Transmit Mapping für TPDO 4 [hex]
p8734 CAN Transmit Mapping für TPDO 5 [hex]
p8735 CAN Transmit Mapping für TPDO 6 [hex]
p8736 CAN Transmit Mapping für TPDO 7 [hex]
p8737 CAN Transmit Mapping für TPDO 8 [hex]
40
7 10
1 AUS1
3 AUS3
P-No. Note
p8741 CAN PDO Konfiguration Bestätigung
p8744 CAN PDO Mapping Konfiguration
1: Predefined Connection Set
2: Freies PDO Mapping
r8750 CAN Gemappte Receive Objekte 16 Bit
r8751 CAN Gemappte Receive Objekte 16 Bit
r8784 CO: CAN Statuswort
p8785 BI: CAN Statuswort Bit 8
p8786 BI: CAN Statuswort Bit 14
p8787 BI: CAN Statuswort Bit 15
p8790 CAN Steuerwort-Verschaltung automatisch
r8795 CAN Steuerwort
r8797 CAN Target Torque
r8820 Identification and Maintenance 0
p8829 CBE20 Remote Controller Anzahl
r8909 PN Device ID
p8920 PN Name of Station
p8921 PN IP Address of Station
p8922 PN Default Gateway of Station
p8923 PN Subnet Mask of Station
p8925 PN Schnittstellen-Konfiguration
0: Keine Funktion
1: Konfiguration aktivieren
2: Konfiguration aktivieren und speichern
3: Konfiguration löschen
p8929 PN Remote Controller Anzahl
0: Automatisierung oder Safety
1: Automatisierung und Safety
r8930 PN Name of Station active
r8931 PN IP Address of Station active
r8932 PN Default Gateway of Station active
r8933 PN Subnet Mask of Station active
r8935 PN MAC Address of Station
r8939 PN DAP ID
r8950 CBE20 Name of Station active
r8955 CBE20 MAC Address of Station
r8960 PN Subslot-Zuordnung
r8961 PN IP Addr Remote Controller 1
r8962 PN IP Addr Remote Controller 2
r8970 CBE20 Subslot-Zuordnung
Getting Started, 03/2012, FW V4.5, A5E03831830A AA
Frequenzumrichter SINAMICS G120C