Preparing Of The Blower Vac Prior To Use; Assembly; Intake/ Air Outlet Tube; Fitting The Debris Collection Bag - FLORABEST FLB 3000 A1 Originalbetriebsanleitung

GB
carefully. Familiarise yourself with the functions
of the controls as well as with the correct and
safe use of the machine.
The operator is responsible for accidents sustained
by other persons or damage to their property.
Preparation
Always wear appropriate clothing, gloves and
sturdy footwear. The wearing of approved protective
goggles is recommended.
By means of visual inspection ensure that no parts of
the device are worn out or damaged before using your
leaf blower/vacuum. Replace parts that are worn out
or damaged. Always check the insulation of the mains
cable and any extensions cables that may be used for
cuts and points of abrasion as well as the condition
of the plugs. All cables with cuts or signs of wear as
well as all damaged plugs and receptacles must be
replaced before using the leaf blower/vacuum.
Before every switch-on of the leaf blower/vacuum,
check that there are no remnants left inside it.
These can present a hazard.
Always ensure that the RCD circuit breaker is
working properly.
Use only replacement parts that are recommended
for this product.
Please proceed with due caution when carrying
out repairs or adjustments.
A leaf blower/vacuum that has been modified or
that is incomplete presents a hazard and so such
a device should not be operated.
Working with your leaf blower/vacuum
Always check the intended working area for
wires or other debris that could damage the leaf
blower/vacuum and injure the operator.
Never feed hard objects such as stones, bottles,
cans or metal parts into the leaf blower/vacuum.
This can damage the machine and could injure
both the operator and bystanders.
Never use the machine whilst other persons, in
particular children or animals, are nearby.
Never let a person who is not familiar with these
operating instructions use the machine.
If possible, do not operate the leaf blower/vacuum
in wet conditions.
Only operate the leaf blower/vacuum when you
are certain that you can stop it quickly in the
event of an emergency.
Never use the leaf blower/vacuum if one or
more of its safety devices is damaged, incorrectly
11
attached or missing.
Ensure that you have adopted a safe and secure
working position before using the machine.
Ensure that all screws and nuts are firmly tightened
before starting the leaf blower/vacuum.
Only use the leaf blower/vacuum in dry environments,
never outside when raining.
Do not use the leaf blower/vacuum if one of its safety
devices is faulty or if a protective cover is missing.
Proceed with great care when cleaning. This
should only be carried out when the leaf blower/
vacuum is switched off and disconnected from
the mains in order to exclude the risk of injury.
Check the mains cable and any extension cables
used for damage and always coil the cable up
tidily and without kinks.
Pull the plug out of the socket:
- Before you leave the leaf blower/vacuum
unattended for any period of time
- Before you remove potential blockages
- Before you check, clean or carry out any work
on the device
If a foreign body or other waste has accidentally
entered the leaf blower/vacuum then stop the device
immediately and only use it again once it has been
checked and you are sure that the complete leaf
blower/vacuum is in a safe operational condition.
If the leaf blower/vacuum makes unusual noises
or starts to vibrate STOP the device immediately,
pull the plug out of the socket and search for the
cause. Excessive vibration can damage the leaf
blower/vacuum and injure the operator.
Preparing of the blower vac prior to use
Warning!
The Vac-Blower must not be used or switched
on until it has been fully assembled.

Assembly

Intake/ Air outlet tube
• Press the button (2.1) and slide the air duct (2.2).
i
The air duct can be adjusted based on user
height, adjust the height up to 300 mm maxi-
mum, 30 mm is a height.
Fitting the debris collection bag
Before fitting the debris collection bag en-
sure that the Vacuum/Blow selector lever
operates smoothly and that it is not obstruct-
(Pic.2 and 3)
(Pic.4 and 5)