EINHELL 43.406.47 Bedienungsanleitung Seite 18

Anleitung_RT_TS_1725_U_SPK1:_
GB
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembling the base frame (Fig. 17/18)
Turn the saw upside down and place it on the
floor.
Use the hex screws and nuts to fasten the four
legs (40) loosely to the saw.
Now fasten the longitudinal struts and cross
struts (41) as well as the four center struts (42)
loosely to the legs.
Be sure to secure the hex screws and nuts only
loosely. Important: The longer struts have to be
used on the sides.
Now mount the rubber feet (43) on the legs and
turn the saw together with the base frame so
that it stands upright on the floor.
Finally, secure all the screws and nuts on the
base frame so that they are tight (Fig. 18).
Bolt the metal brackets (48) to the inside of the
legs (40) as shown in Figure 30. These metal
brackets (48) must be used to secure firmly the
saw to the ground before it is started.
7.2 Table width extension and length extension
(Fig. 19/20)
Use the screws and nuts to fasten the table
width extension and length extension (35/36)
loosely to the saw table (1) (Fig. 19).
Screw the supports (27) loosely onto the saw
housing and onto the table width extension or
length extension (short supports for the width
extension, long supports for the length
extension).
Align the table width extension and length
extension level with the saw table (1).
Finally, tighten all screws. (Fig. 20)
7.3 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (44) in the
splitter.
Do not tighten the screw (15) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
18
13.01.2009 10:20 Uhr Seite 18
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.4. Setting the splitter (Fig. 3/6/7/8)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place.
Remove the saw blade guard (see 7.3).
Take out the table insert (6) (see 7.5).
Slacken the fixing screw (20).
7.4.1. Setting for maximum cuts (Fig. 6/7/8)
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) equals approx. 10 cm.
The distance between the blade (4) and the
splitter (5) should be 3-5 mm.
Retighten the screw (20) and mount the table
insert (6) (Fig. 7).
7.4.2. Setting for concealed cuts (Fig. 6/7/8)
Push down the splitter (5) to the point where the
tip of the splitter is 2 mm below the uppermost
saw tooth tip.
The distance between the splitter (5) and the
saw blade (4) should again be 3-5 mm (see Fig.
6).
Retighten the screw (20) and mount the table
insert (6).
Important! After you make a concealed cut,
be sure to refit the guard hood.
Please note that the cutting height will be
reduced to approx. 55 mm if you leave the
splitter in the lower position.
The setting of the splitter has to be checked
each time after changing the saw blade.
7.5 Changing the table insert (Figure 7)
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2).
Remove the 2 countersunk head screws (34).
Take out the worn table insert (6).
To fit the replacement table insert, proceed in
reverse order.