Technical Data; Noise Emission Values; Before Putting The Machine Into Operation - EINHELL 43.406.47 Bedienungsanleitung

Anleitung_RT_TS_1725_U_SPK1:_
4. Important information
Please read the directions for use carefully and
observe the information provided. It is important to
consult these instructions in order to acquaint
yourself with the machine, its proper use and safety
precautions.
The corresponding safety information can be found
in the enclosed booklet.
Caution:
Laser radiation.
Do not look into the beam!
Laser class 2
Achtung
Laserstrahlung
Nicht in den Strahl blicken!
Laserspezifikation nach
EN 60825-1: 1994+A11:1996
Laser Klasse 2 1894S-8x11
P: ≤ 1 mW
Ï: 650 nm
Protect yourself and your environment from
accidents by taking the appropriate precautionary
measures.
Do not look directly into the laser beam with the
naked eye.
Never look directly into the laser path.
Never direct the laser beam at reflecting surfaces,
persons or animals. Even a low output laser beam
can inflict injury on the eye.
Caution: It is vital to follow the work procedures
described in these instructions. Using the tool in
any other way may result in hazardous exposure
to laser radiation.
Never open laser module.
When the tool is not going to be used for an
extended period of time, the batteries should be
removed.

Noise emission values

Sound pressure level L
pA
Sound power level L
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
13.01.2009 10:20 Uhr Seite 17
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.

5. Technical data

AC motor
Power P
Idle speed n
0
Carbide saw blade
Number of teeth
Bench size
Table width extension, left/right
Table length extension, rear
Cutting height max.
Height adjustment
Tilting saw blade
Extractor socket
Weight
Laser class
Laser wavelength
Laser output
Laser power supply
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of
the cycle.
6. Before putting the machine into
operation
mode
Unpack the bench-type circular saw and check it
96,2 dB(A)
for damage which may have occurred in transit.
109,2 dB(A)
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
GB
230 V 50Hz
S6 40% 1700 W
4800 min -1
Ø 250 x Ø 30 x 2.8 mm
24
626 x 445 mm
626 x 250 mm
445 x 320 mm
73 mm/90°
53 mm / 45°
infinite 0 -73 mm
infinite 0° - 45°
Ø 35 mm
33,5 kg
2
650 nm
≤ 1 mW
2 x 1.5 V (AAA)
17