Specifications; Additional Safety Rules - Makita 3620 Betriebsanleitung

ENGLISH
1 Tighten
2 Loosen
3 Hold
4 Screw
5 Stopper pole
6 Lock lever
7 Depth pointer
8 Adjusting hex bolt
9 Stopper block
10 Hex nut

SPECIFICATIONS

Model
Collet capacity ........................................... 8 mm or 3/8''
Plunge capacity ............................................. 0 – 35 mm
-1
No load speed (min ) .......................................... 27,000
Overall height ..................................................... 211 mm
Net weight ............................................................. 2.4 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a ''live'' wire will make exposed metal
parts of the tool ''live'' and shock the operator.
2. Wear hearing protection during extended period
of operation.
3. Handle the bits very carefully.
4. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged bit
immediately.
5. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
6. Hold the tool firmly with both hands.
7. Keep hands away from rotating parts.
8. Make sure the bit is not contacting the workpiece
before the switch is turned on.
9. Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
10. Be careful of the bit rotating direction and the
feed direction.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Always switch off and wait for the bit to come to a
complete stop before removing the tool from
workpiece.
6
Explanation of general view
11 Switch trigger
12 Feed direction
13 Workpiece
14 Bit revolving direction
15 (View from the top of the
tool)
16 Correct bit feed direction
17 Guide bar
18 Straight guide
13. Do not touch the bit immediately after operation;
3620
14. Always lead the power supply cord away from the
15. Do not smear the tool base carelessly with thinner,
16. Draw attention to the need to use cutters of the
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing router bit (Fig. 1)
Important:
Always be sure that the tool is switched off and unplugged
before installing or removing the bit.
Insert the bit all the way into the collet cone and tighten
the collet nut securely with the two wrenches.
A 6 mm or 1/4'' collet cone is also provided as standard
equipment besides the 8 mm or 3/8'' collet cone that is
factory installed on the tool. Use the correct size collet
ENB033-2
cone for the bit which you intend to use.
To remove the bit, follow the installation procedure in
reverse.
CAUTION:
Do not tighten the collet nut without inserting a bit, or the
collet cone will break.
Adjusting the depth of cut (Fig. 2, 3 & 4)
Place the tool on a flat surface. Loosen the screw
securing the stopper pole.
Loosen the lock lever and lower the tool body until the bit
just touches the flat surface. Tighten the lock lever to lock
the tool body.
Next, lower the stopper pole until it makes contact with
the adjusting hex bolt. Align the depth pointer with the ''0''
graduation.
Raise the stopper pole until the desired depth of cut is
obtained. The depth of cut is indicated on the scale (1 mm
or 1/16'' per graduation) by the depth pointer. Then
tighten the screw to secure the stopper pole.
Now, your predetermined depth of cut can be obtained by
loosening the lock lever and then lowering the tool body
until the stopper pole makes contact with the adjusting
hex bolt.
19 Wing bolt
20 Screw
21 Base plate
22 Templet guide
23 Bit
24 Base
25 Templet
26 Vacuum head
27 Screws
it may be extremely hot and could burn your skin.
tool towards the rear.
gasoline, oil or the like.
They may cause cracks in the tool base.
correct shank diameter and which are suitable for
the speed of the tool.