Specifications - Makita DTWA070 Betriebsanleitung

ENGLISH (Original instructions)

SPECIFICATIONS

Model:
Fastening capacities
Maximum fastening torque
Torque range
Square drive
No load speed (RPM)
Impacts per minute
Overall length
Rated voltage
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for fastening bolts and nuts.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-2:
Model DTWA070
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTWA100
Sound pressure level (L
Sound power level (L ) : 104 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTWA140
Sound pressure level (L
Sound power level (L ) : 107 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTWA190
Sound pressure level (L
Sound power level (L ) : 106 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Standard bolt
High tensile bolt
) : 92 dB(A)
pA
) : 93 dB(A)
pA
) : 96 dB(A)
pA
) : 95 dB(A)
pA
DTWA070 DTWA100
M5 - M12
M5 - M10
65 N•m 95 N•m
Approx. Approx.
5 - 40 N•m 6 - 65 N•m
9.5 mm
-1
0 - 2,500 min
-1
0 - 3,700 min
144 mm 151 mm
1.1 - 1.4 kg 1.2 - 1.4 kg
BL1415N / BL1415NA / BL1430 / BL1430B / BL1440 / BL1450 /
BL1460A / BL1460B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
5 ENGLISH
DTWA140
M6 - M16
M6 - M12
140 N•m
Approx.
18 - 80 N•m 25 - 125 N•m
12.7 mm
-1
0 - 2,700 min 0 - 2,600 min
-1
0 - 3,300 min 0 - 3,000 min
158 mm
D.C. 14.4 V
1.2 - 1.5 kg 1.3 - 1.6 kg
DC18SH
DTWA190
M8 - M16
M8- M14
185 N•m
Approx.
-1
-1