Setting Cue Points; Changing Playback Speed - Pioneer DVJ-X1 Bedienungsanleitung

Basic Operations
LOOP IN/
REALTIME
CUE
REV 1,
FWD ¡
CUE
PLAY/PAUSE
6
Jog dial

Setting cue points

# This function is not supported when the rear panel mode select
switch (MODE NORMAL/DJ) is set to the NORMAL position.
When a cue point has been previously set, pressing the CUE button
during playback will cause the player to move instantly to the cue point
and enter the cue standby mode.
¶ Storing to memory may not be possible while the jog dial's audio/
video memory status display is flashing.
I Setting a cue point with VINYL mode OFF
1. During playback, press the PLAY/PAUSE (6) button near
the point you wish to set as a cue point. The player will
enter the pause mode.
2. Search for the precise cue point.
¶ Using frame numbers:
The cue point position can be set in units of single frames (75
frames per second).
Using the jog dial or the search buttons (REV1, FWD¡), ad-
vance or reverse the frames to the desired point. One revolution
of the jog dial is equivalent to 135 frames; each time the search
button is pressed, the disc moves one frame in the direction cor-
responding to the button.
¶ Search for cue point using audible pause:
Rotate the jog dial slowly and reverse the disc to the instant just
prior to the point from which you wish to begin playback (the cue
point will be set at the point immediately after the sound heard
during audible pause).
3. When you have found the desired cue point using the
frame number or audible pause, press the CUE button.
¶ The CUE button's rim indicator will light to indicate that the new
cue point has been recorded in memory.
¶ During DVD playback, a thumbnail of the cue point appears on the
preview monitor screen.
¶ During CD or MP3 playback, the cue point's track number and
time are displayed on the preview screen.
¶ When a new cue point is recorded in memory, the previously
memorized cue point will be erased.
[Modifying a cue point]
1. During playback, press the CUE button.
¶ Playback will return to the set cue point and enter cue standby.
2. Use the search buttons (REV1, FWD¡) to enter audi-
ble pause mode.
3. Find the new cue point by performing steps 2 and 3 of
the above section "I Setting a cue point with VINYL mode
OFF".
36
En <DRB1388>
I Setting a cue point with VINYL mode ON
MODE
1. As playback nears the desired cue point, either press the
NORMAL/DJ
2. While pressing the surface of the jog dial, listen to the
3. When the sound is at the desired cue point, continue hold-
HYPERJOG
MODE
JOG MODE
TEMPO
[Modifying a cue point]
MASTER
TEMPO
1. During playback, press the CUE button.
TEMPO
2. Perform steps 2 and 3 of the previous section "I Setting
TEMPO
RESET
I Real time cue
During forward playback, press the LOOP IN/REALTIME CUE
button at the place you wish to set as cue point.
¶ This point will be recorded as the new cue point.
I Confirm cue point (cue point sampler)
After setting a cue point, depress the CUE button while the
unit is in the cue standby mode.
¶ The audio and video from the cue point will be played back while the
I To return to a cue point (back cue)
During playback, press the CUE button.
¶ Playback will return to the previously set cue point, sound will be
¶ Press the PLAY/PAUSE (6) button to resume playback instantly
¶ When playing a DVD that prohibits title or other searches, playback
¶ In the case of MP3, back cue is supported only within one and the

Changing playback speed

# This function is not supported when the rear panel mode select
Slide the TEMPO control slider forward or back.
When the slider is moved forward (+), playback speed will increase, and
when moved back (–), playback speed will decrease.
¶ The rate of tempo change is displayed.
¶ It is also possible to change playback speed without affecting the
I Selecting a tempo control range
Press the TEMPO button.
Each time the button is pressed, the TEMPO control slider's variable
control range alternates between the values ±6 %, ±10 %, ±16 %, and
WIDE. The range can be adjusted in increments of 0.02 % (for ±6 %),
0.05 % (for ±10 %), 0.05 % (for ±16 % ), and 0.5 % (for WIDE).
¶ The variable control range setting value is shown by the tempo con-
¶ The variability in the WIDE range is:
I Tempo Reset
Press the TEMPO RESET button.
The TEMPO RESET indicator lights and the tempo change rate is reset to
"0" (normal tempo), regardless of the position of the TEMPO control slider.
¶ If the TEMPO RESET button is pressed once again, tempo reset is
top surface of the jog dial or press the PLAY/PAUSE (6)
button to set the unit in pause mode.
playback sound as you rotate the dial, and return play-
back to the point just before the spot you wish to use as
the cue point.
ing the surface of the jog dial depressed, and press the
CUE button.
¶ The CUE button's rim indicator will light to indicate that the new
cue point has been recorded in memory.
¶ When a new cue point is recorded in memory, the previously
memorized cue point will be erased.
¶ Playback will return to the set cue point and enter cue standby.
a cue point with VINYL mode ON".
¶ In the same way as for VINYL mode OFF, The search buttons
(REV1, FWD¡) can also be used to modify a cue point.
CUE button is held depressed, allowing you to confirm the point.
muted, and the monitor screen will display black background as the
unit enters the cue standby mode.
from the cue point.
will continue, and the prohibited mark
the similar mark will appear on the preview monitor screen.
same folder.
switch (MODE NORMAL/DJ) is set to the NORMAL position.
pitch ( P.37, "Setting master tempo").
trol range indicator, as well as in the onscreen display.
±100% (CD)
+70% to –100% (DVD, MP3)
canceled, and the tempo returns to the value set with the TEMPO
control slider.
will appear in the display;