Specifications - Hitachi DV 14DMR Bedienungsanleitung

5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of fire
when used with another battery pack.
b) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
CORDLESS IMPACT DRIVER DRILL SAFETY
WARNINGS
1. Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.

SPECIFICATIONS

POWER TOOL
Model
No-load speed (Low/High)
No-load impact rate (Low/High)
Brick
(Depth 30 mm)
Wood
Drilling
(Thickness 18 mm)
Capacity
Metal
(Thickness 1.6 mm)
Machine screw
Driving
Wood screw
Rechargeable battery
Weight
2. Use auxiliary handles supplied with the tool.
3. When drilling in wall, floor or ceiling, check for
4. Bring the battery to the shop from which it was
5. When mounting a bit into the keyless chuck, tighten
6. Always charge the battery at a temperature of 0 –
7. When one charging is completed, leave the charger
8. Do not allow foreign matter to enter the hole for
9. Never disassemble the rechargeable battery and
10. Never short-circuit the rechargeable battery. Short-
11. Do not dispose of the battery in fire.
12. Using an exhausted battery will damage the charger.
13. Do not insert object into the air ventilation slots of
DV14DMR
0 – 400 / 0 – 1750 min
0 – 4800 / 0 – 21000 min
14 mm
45 mm
Steel: 13 mm,
Aluminum: 13 mm
6 mm
8 mm (diameter) × 75 mm (length)
(Requires a pilot hole)
EB14B: Ni-Cd 14.4 V (2.0 Ah 12 cells)
EB1424: Ni-Cd 14.4 V (2.4 Ah 12 cells)
EB1426H: Ni-MH 14.4 V (2.6 Ah 12 cells) EB1826HL: Ni-MH 18 V (2.6 Ah 15 cells)
EB1430H: Ni-MH 14.4 V (3.0 Ah 12 cells) EB1830HL: Ni-MH 18 V (3.0 Ah 15 cells)
2.5 kg
Loss of control can cause personal injury.
buried electric power cord, etc.
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose
of the exhausted battery.
the sleeve adequately. If the sleeve is not tight, the
bit may slip or fall out, causing injury.
40°C. A temperature of less than 0°C will result in
over charging which is dangerous. The battery
cannot be charged at a temperature higher than
40°C.
The most suitable temperature for charging is that
of 20 – 25°C.
for about 15 minutes before the next charging of
battery.
Do not charge more than two batteries
consecutively.
connecting the rechargeable battery.
charger.
circuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
If the battery is burnt, it may explode.
the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
–1 0 – 400 / 0 – 1800 min
–1
0 – 4800 / 0 – 21600 min
Steel: 13 mm,
Aluminum: 13 mm
8 mm (diameter) × 100 mm (length)
(Requires a pilot hole)
EB1820L: Ni-Cd 18 V (2.0 Ah 15 cells)
EB1824L: Ni-Cd 18 V (2.4 Ah 15 cells)
English
DV18DMR
–1
–1
16 mm
50 mm
6 mm
2.7 kg
8