Maintenance - EINHELL 34.365.30 Originalbetriebsanleitung

Preventing recoil
When you work with the blade, there is a risk of
recoil if it strikes solid objects such as tree trunks,
branches, tree stumps, stones or the like. This will
throw the equipment backwards in the direction
opposite to the rotation of the tool. This can cause
you to lose control of the equipment. Do not use
the blade near fences, metal posts, boundary
stones or foundations. For cutting dense stalks,
position the blade as shown in Fig. 9f to prevent
recoil.

9. Maintenance

Always switch off the equipment and pull out the
spark boot plug before carrying out any mainte-
nance work.
9.1 Replacing the line spool/cutting line
1. Dismantle the line spool (13) as described in
section 5.1.6. Press the spool together (Fig.
12a) and remove one half of the housing (Fig.
12b).
2. Take the line spool out of the line spool
housing (Fig. 12c).
3. Remove any remaining cutting line.
4. Place the new cutting line in the center and
attach the resulting loop to the recess in the
spool splitter (Fig. 12d).
5. Wind the line on to the spool counter-clockwi-
se with tension. The spool splitter will separa-
te the two halves of the nylon line (Fig. 12e).
6. Hook the last 15 cm of the two ends of the
line to the line holders opposite the line spool
(Fig. 12f).
7. Thread the two ends of the line through the
metal eyelets in the line spool housing (Fig.
12c).
8. Press the line spool into the line spool
housing.
9. Cut the excess line to a length of around 13
cm. This will reduce the load on the engine
when starting up and warming up.
10. Fit the line spool again. See section 5.1.6. If
you are replacing the complete line spool,
ignore points 3-6.
9.2 Grinding the safety hood blade
The safety hood blade can become blunt over
time. When you notice this, undo the screw hol-
ding the safety hood blade on the safety hood.
Clamp the blade in a vise. Sharpen the blade with
a fl at fi le and make sure that the angle of the cut-
Anl_GC_BC_43_I_AS_SPK1.indb 24 Anl_GC_BC_43_I_AS_SPK1.indb 24
GB
ting edge is not altered in the process. File in one
direction only.
9.3 Maintenance of the air fi lter (Fig. 10a-10c)
Soiled air fi lters reduce the engine output by sup-
ply too little air to the carburetor. Regular checks
are therefore essential. The air fi lter (10) should
be checked after every 25 hours of use and clea-
ned if necessary. If the air contains a lot of dust,
the air fi lter should be checked more frequently.
1. Remove the air fi lter cover (Fig. 10a).
2. Remove the fi lter element (Fig. 10b/10c).
3. Clean the fi lter element by tapping it or
blowing it.
4. Assemble in reverse order.
Important: Never clean the air fi lter with petrol or
infl ammable solvents.
9.4 Maintenance of the spark plug
(Fig. 11a-11b)
Spark plug sparking gap = 0.6mm. Tighten the
spark plug with a torque of 12 to 15 Nm. Check
the spark plug for dirt and grime after 10 hours of
operation and if necessary clean it with a copper
wire brush. Thereafter service the spark plug after
every 50 hours of operation.
1. Pull out the spark plug connector (16) (Fig.
11a).
2. Remove the spark plug (Abb. 11b) with the
supplied spark plug wrench (27).
3. Assemble in reverse order.
9.5 Carburetor settings
Important. Settings on the carburetor may only be
made by authorized customer service personnel.
The air fi lter cover must be removed before any
work on the carburetor, as shown in Figures
10a-10c.
Setting the throttle cable:
If the maximum speed of the equipment drops
over time and you have ruled out all the other
possible causes listed in section 12 „Troubleshoo-
ting", it may be necessary to adjust the throttle
cable. First of all check whether the carburetor
opens fully when the throttle handle is pressed
right through. This is the case if the carburetor
slide (Fig. 13a) is completely opened when the
throttle is fully activated. Figure 13a shows the
correct setting. If the carburetor slide is not com-
pletely open, it must be adjusted.
The following steps are required to adjust the
throttle cable:
- 24 -
26.10.2016 07:12:41 26.10.2016 07:12:41