Specifications; Standard Accessories - Hitachi UM 16VST Bedienungsanleitung

5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
PRECAUTIONS ON USING THE MACHINE
1. Do not use the power tool for explosive materials
(e. g., easily infl ammable solvents).
Power tools produce sparks which could ignite
developing vapours.
2. In case the power tool should fall into the material
to be stirred, pull the plug immediately and have
the power tool checked by an after-sales service
agent.
Material that has penetrated the power tool can cause
damage and lead to an electric shock.

SPECIFICATIONS

Model
Voltage (by areas)*
Power input
Speed change
No load speed
Stirrer paddle
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Stirrer paddle 160 mm (UM16VST) or 120 mm
(UM12VST) ................................................................... 1
(2) Wrench ......................................................................... 2
(3) 1 pair of spare carbon brush ......................................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
Mixing pulverised building materials such as mortar,
plaster, adhesives, as well as solvent-free paint, varnish
and similar substances.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
UM16VST
1500 W*
1
150 – 300 min 300 – 650 min
-1
160 mm
5.6 kg
3. When working with the machine, always hold it
fi rmly with both hands and provide for a secure
stance.
The power tool is guided more secure with both hands.
4. Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
5. Take protective measures when dust can develop
during working that is harmful to one's health,
combustible or explosive.
Example: Some dusts are regarded as carcinogenic.
Wear a dust mask and work with dust/chip extraction
when connectable.
6. Always wait until the machine has come to a
complete stop before placing it down.
The tool insert can jam and lead to loss of control over
the power tool.
7. Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains
plug when the cable is damaged while working.
Damaged cables increase the risk of an electric shock.
8. When operating a mixer with wet material avoid
splashes up to the motor part.
9. Connect machines that are used in the open via a
residual current device (RCD).
230V
2 1
150 – 300 min
-1
4. Mounting and dismounting of the stirrer paddle
(Fig. 2)
CAUTION
To avoid serious accident, ensure the switch is in the
OFF position, and the power source is disconnected.
(1) Screw the stirrer paddle onto the spindle. Hold the
spindle in place with wrench and turn the stirrer paddle
with another wrench in the clockwise direction (viewed
from the front side). Tighten securely.
(2) The stirrer paddle is disassembled in reverse order.
5. High-speed/Low-speed changeover
Prior to changing speed, ensure that the switch is in the
OFF position, and the machine has come to a complete
stop.
To change speed, rotate the gear shift dial as indicated
by the arrow in Fig. 3. The numeral "1" engraved on
the machine body denotes low speed, the numeral "2"
denotes high speed.
If it is hard to turn the gear shift dial, turn the spindle
slightly in either direction and then turn the gear shift dial
again.
HOW TO USE
1. Switch operation (Fig. 4)
○ When the trigger is depressed, the tool rotates. When
the trigger is released, the tool stops.
○ Pulling the trigger and pushing the stopper, it keeps
the switched-on condition which is convenient for
continuous running. When switching off , the stopper can
be disconnected by pulling the trigger again.
English
UM12VST
1100 W*
2
300 – 650 min
-1 -1
120 mm
5.4 kg
7