How To Use - Hitachi DV 14DSL Bedienungsanleitung

CAUTION:
When the battery charger has been continuosly used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next
charging.
If the battery is recharged when it is warm due to
battery use or exposure to sunlight, the pilot lamp
map light in green.
The battery will not be recharged. In such a case, let
the battery cool before charging.
When the pilot lamp flickers in red (at 0.2-second
intervals), check for and take out any foreign objects
in the charger's battery installation hole. If there are
no foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your authorized
Service Center.
PRIOR TO OPERATION
1. Setting up and checking the work environment
Check if the work environment is suitable by following
the precautions.

HOW TO USE

1. Confirm the clutch dial position (see Fig. 5)
The tightening torque of this unit can be adjusted
according to the clutch dial position, at which the
clutch dial is set.
(1) When using this unit as a screwdriver, line up the one
of the numbers "1, 3, 5 ... 22" on the clutch dial, or
the dots, with the triangle mark on the outer body.
(2) When using this unit as a drill, align the clutch dial
drill mark " " with the triangle mark on the outer
body.
(3) When using this unit as an impact drill, align the cap
hammer mark " " with the triangle mark on the
outer body.
CAUTION:
The clutch dial cannot be set between the numerals
"1, 3, 5 ... 22" or the dots.
Do not use with the clutch dial numeral between
"22" and the line at the middle of the drill mark.
Doing so may cause damage. (See Fig. 6)
2. Tightening torque adjustment
(1) Tightening torque
Tightening torque should correspond in its intensity to
the screw diameter. When too strong torque is used, the
screw head may be broken or be injured. Be sure to adjust
the clutch dial position according to the screw diameter.
Work
Brick
Wood
Drilling
Steel
Aluminum
Machine screw
Driving
Wood screw
(2) Tightening torque indication
The tightening torque differs depending on the type
of screw and the material being tightened.
The unit indicates the tightening torque with the numbers
"1, 3, 5 ... 22" on the clutch dial , and the dots. The
tightening toque at position "1" is the weakest and the
torque is strongest at the highest number. (See Fig. 5)
(3) Adjusting the tightening torque
Rotate the clutch dial and line up the numbers "1, 3,
5, ... 22" on the clutch dial, or the dots, with the
triangle mark on the outer body. Adjust the clutch
dial in the weak or the strong torque direction
according to the torque you need.
CAUTION:
The motor rotation may be locked to cease while the
unit is used as drill. While operating the driver drill,
take care not to lock the motor.
Too long hammering may cause the screw broken
due to excessive tightening.
3. Rotation to Impact changeover (See Fig. 5)
The "Rotation (Rotation only)" and "Impact (Impact
+ Rotation)" can be switched by aligning the drill
mark "
mark on the outer body.
To make holes in the metal, wood or plastic, switch
to "Rotation (Rotation only)".
To make holes in bricks or concrete blocks, switch to
"Impact (Impact + Rotation)".
CAUTION
If an operation which is normally performed at the
"Rotation" setting is performed at "Impact " setting,
the effect of making holes does not only increase but
it may also damage the bit or other parts.
4. Change rotation speed
Operate the shift knob to change the rotational speed. Move
the shift knob in the direction of the arrow (see Figs. 7 and 8).
When the shift knob is set to "LOW", the drill rotates at a low
speed.!»en set to "HIGH", the drill rotates at a high speed.
CAUTION:
When changing the rotational speed with the shift
knob, confirm that the switch is off.
Changing the speed while the motor is rotating will
damage the gears.
When setting the shift knob to "HIGH" (high speed)
and the position of the clutch dial is "17" or "22", it
may happen that the clutch is not engaged and that
the motor is locked. In such a case, please set the
shift knob to "LOW" (low speed).
If the motor is locked, immediately turn the power
off. If the motor is locked for a while, the motor or
battery may be burnt.
5. The scope and suggestions for uses
The usable scope for various types of work based on the
mechanical structure of this unit is shown in Table 4.
Table 4
Use for drilling purpose.
Use the bit or socket matching the screw diameter.
Use after drilling a pilot hole.
" or the hammer mark " " with the triangle
Suggestions
English
10