Stiga PARK PRO 16 Montageanleitung Seite 16

EN
If the cables are interchanged, the gen-
erator and the battery will be damaged.
Tighten the cables securely. Loose ca-
bles can cause a fire.
The engine must never be driven with
the battery disconnected. There is a risk
of serious damage to the generator and
the electrical system.
When the battery has been rectified, install the fuel
tank as follows:
Check that the petrol hose is not
clamped against the hydraulic pump
and does not come into contact with
this. The hydraulic pump becomes very
hot during operation. Risk of fire.
1. Place the petrol tank on the brackets. Check that
the petrol hose is not touching the hydraulic
pump.
2. Install the clamps and tighten the wing nuts
(4:O).
2.5 Seat, FIG 6
1. Remove the following components from the
seat bracket:
• 4 Nuts (for transport locking, not used).
• 4 Screws.
• 4 Shoulder washers.
2. Position the seat over the mounting in the seat
bracket.
3. Install the shoulder washers on the screws.
4. Insert the screws with the attached shoulder
washers through the slots in the seat bracket and
the holes in the seat plate. Screw the seat into
place.
Tightening torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
5.Check that the seat moves easily in the
slots in the bracket.
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
2.6 Arm rests (Pro20, Pro25, Pro
Svan)
The arm rests and the installation components are
supplied in a separate box. Assemble as follows:
1. Assemble the left and right mounts onto the
seat. Use 3 screws (8:Q) supplied at each side.
2. Assemble the arm rests with screws (9:R), nuts
(9:S) and spacers (9:T).
3. Tighten the screws so that the arm rests simply
can be folded up/down.
16
ENGLISH
2.7 Steering wheel
In order to minimise the axial play in the steering
column, the shim washers (10:B) and/or (10:C)
must be installed on the steering column between
the steering column jacket and the bracket as fol-
lows.
1. Install the steering column jacket on the steer-
ing column and secure by knocking in the ten-
sion pin (10:A) approximately 1/3 of its length.
2. Pull the steering column jacket and the steering
column up.
3. From the outside, check whether no washers,
the 0.5 mm washer, the 1.0 mm washer or both
washers can be inserted into the gap. The wash-
er/washers must not be forced in, as there must
be a little axial play.
4. Pull out the cotter pin and dismantle the steering
wheel jacket.
5. Install the washer/washers in accordance with
point 3 above.
6. Install the steering column jacket on the steer-
ing column and secure by knocking in the ten-
sion pin fully. Use a counterhold.
2.8 Towing plate
Install the towing plate (11:I) at the rear of the ma-
chine. Use the screws and the nuts (11:J, H).
Tightening torque: 22 Nm.
2.9 Tyre pressure
Check the air pressure in the tyres. Correct air
pressure:
Front: 0.6 bar (9 psi)
Rear: 0.4 bar (6 psi)
2.10Quick-release mountings
The quick-release mountings and installation in-
structions are supplied in a separate box.
Install the quick-release mountings on the front ax-
les of the machine.
2.11Accessories
For the installation of accessories, see separate in-
stallation guide supplied with each accessory.
Note: The cutting deck is regarded as an accessory
here.