Stiga PARK PRO 16 Montageanleitung Seite 15

1 GENERAL
This symbol indicates WARNING. Per-
sonal injury and/or damage to property
may result if the instructions are not
followed carefully.
You must read these instructions and
the accompanying pamphlet "SAFETY
INSTRUCTIONS" carefully, before the
assembly begin.
2 ASSEMBLY
To avoid injury and damage to people
and property, do not use the machine
until all the measures in this instruction
have been carried out..
2.1 Accessories bag
The machine is supplied with a plastic bag contain-
ing components which shall be used during the as-
sembly. The bag contains (fig. 1):
Pos. No. Designation
A 1 Pin
B 1 Shim washer
C 1 Shim washer
D 2 Ignition key
E 2 Screw for battery
F 2 Nut for battery
G 2 Screw
H 2 Nut
I 1 Towing plate
2.2 References
The figures in these instructions for use are num-
bered 1, 2, 3, etc.
Components shown in the figures are marked A, B,
C, etc.
A reference to component C in figure 2 is written
"2:C".
2.3 Engine casing (2:M)
In order to access the fuel cock, battery
and engine, the machine has an engine
casing that can be opened. The engine cas-
ing is locked with a rubber strap.
The engine casing is opened as follows:
1. Undo the rubber strap (2:N) at the front edge of
the casing.
2. Carefully lift the engine casing back.
Close in the reverse order.
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.
ENGLISH
2.4 Battery
The battery is a valve-regulated battery with 12 V
nominal voltage. The battery fluid does not need to
and cannot be checked or topped up. The only
maintenance that is required is charging, for exam-
ple after extended storage.
2.4.1 Charging with the engine
The battery can be charged using the engine's gen-
erator as follows:
1. Install the battery in the machine as shown be-
low.
2. Place the machine outdoors or install an extrac-
tion device for the exhaust fumes.
Dimension
6 x 36 3. Start the engine according to the instructions in
the user guide.
16 x 38 x 0.5
4. Allow the engine to run continuously for 45
16 x 38 x 1.0
minutes.
5. Stop the engine. The battery will now be fully
charged.
8 x 20
2.4.2 Charging using battery charger
M8
When charging using a battery charger, a battery
charger with constant voltage must be used.
Contact your dealer to purchase a battery charger
with constant voltage.
The battery can be damaged if a standard type bat-
tery charger is used.
2.4.3 Installation
The battery is placed under the tank. To access the
battery, first dismantle the fuel tank as follows:
1. Open the engine casing.
2. Close the fuel cock, see 3.
3. Unscrew the two wing nuts (4:O) and remove
the clamps.
4. Carefully lift up the petrol tank.
During installation, see fig. 5. First connect the red
cable to the battery's positive terminal (+). Then
connect the black cable to the battery's negative
terminal (-).
If acid comes into contact with the eyes
or skin, this can cause serious injuries.
If any part of the body has come into
contact with acid, rinse immediately
with copious amounts of water and seek
medical assistance as soon as possible.
The battery must be fully charged be-
fore being used for the first time. The
battery must always be stored fully
charged. If the battery is stored while
discharged, serious damage will occur.
If the cables are disconnected/connect-
ed in the wrong order, there is a risk of
a short-circuit and damage to the bat-
tery.
EN
15